Operating and installation instructions Oven H 5681 BPL H 5681 BPR en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
Any other use is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the appliance.
Page 8
Warning and Safety instructions Technical safety Before connecting the appliance, make sure that the connection data on Installation, maintenance and the data plate (voltage and connected repairs may only be carried out by a load) match the mains electricity suitably qualified and competent supply.
If the supply cord is damaged, it even cause it to catch fire. must be replaced by a Miele approved Do not use the "Full grill", "Economy service technician to avoid a hazard.
Page 10
Warning and Safety instructions If using alcohol in your recipes, high If using a tray made by a different temperatures can cause the alcohol to manufacturer, make sure that there is a vaporise and even to ignite on the hot gap of at least 6 cm between the heating elements.
Page 11
Only use the Miele food probe Make sure that nothing gets trapped supplied with this oven. between the door and the oven If a replacement is necessary it can be compartment.
Caring for the environment Disposal of the packing Disposing of your old material appliance The transport and protective packing Electrical and electronic appliances has been selected from materials which often contain materials which, if are envoronmentally friendly for handled or disposed of incorrectly, disposal, and should be recycled.
Guide to the appliance H 5681 BPL Control panel Door lock for pyrolytic operation Top heat / grill element with receiver for the wireless food probe Steam inlets for Moisture plus Back panel with air inlet for the fan Side runners with five shelf levels...
Features Oven controls Cooling system In addition to operating the various A cooling fan will come on cooking programmes to bake, roast automatically when a cooking and grill, the controls also offer the programme is started. The cooling fan following: mixes hot air from the oven cavity with cool room air before venting it out into –...
Features Energy saving features Energy save mode The oven switches off automatically to Lighting save energy if, at the end of an Auto- matic programme or a cooking The oven lighting is set to switch off 15 seconds after the start of a cooking programme with Automatic switch-off, programme (default setting).
Features User instructions PerfectClean treated surfaces The User instructions supplied with The following surfaces are all treated your appliance in addition to these with a special PerfectClean finish: Operating and installation instructions – Side runners, contains detailed information about the –...
These and other accessories are also them being pulled right out when they available to order from the Miele Spare only need to be partially pulled out. Parts Department, your Dealer or via The trays and rack can then only be the internet at www.miele-shop.com.
The FlexiClip telescopic runners can be the two rails that make up a shelf level. clipped into any of the existing shelf The telescopic runner with the Miele runners and pulled out of the oven to logo is fitted on the right.
Features Changing the position of the Food probe FlexiClip telescopic runners Make sure that the oven has cooled down before moving the FlexiClip This appliance is supplied with a runners. wireless food probe. Take care not to burn yourself on them.
Features Anti-splash insert (depending on model) The anti-splash insert should be placed in the universal tray when grilling or roasting. The juices from the food being cooked collect under the anti-splash insert. This prevents them from spitting and making the oven dirty. The juices can then be used for making gravy and sauces.
Miele{home Miele|home communication enabled appliances use the household electrical network to communicate information about their operational status and the progress of the programme to a master appliance These instructions are for a Optional accessories communication enabled oven that – Required: Communication module...
Controls The appliance is operated via the display and the electronic sensors next to and below the display. These react to finger contact. A keypad tone will sound each time a sensor is touched. The volume of the keypad tone can be adjusted or switched off altogether (see "Settings - Volume - Keypad tone").
Controls Display Main menu ß Fan plus All information about functions, temperature, cooking durations, Auto- ß Conventional heat matic programmes and settings is ß Full grill shown in the display. ß Pyrolytic After the appliance has been switched on by touching the sensor, the Main ß...
Controls Symbols The following symbols will appear in the display in addition to the text: Symbol Meaning Appears beside an option and is allocated to a sensor C. You select the option you want by touching the sensor beside the dot. A maximum of 3 options can be shown in the display.
Page 25
Controls When a function is selected, the following symbols may appear in the display, depending on setting: Symbol Meaning Duration Finish Start time Programme finished Rapid heat-up phase, Rapid searing phase Heating-up phase, Searing phase Core temperature when using the food probe Fan plus, Fan heat Intensive bake Moisture plus...
Functions Your oven has a range of oven functions for preparing a wide variety of recipes. These include: Top heat/grill element (under the roof of the oven) Bottom heating element (under the floor of the oven) Ring heating element (behind the intake vent for the fan) Fan (behind the intake vent for the fan) Steam injection system These components are combined in various ways, depending on the oven...
Page 27
Functions Function Notes Conventional heat – For baking traditional recipes, e.g. fruit cake, casseroles. – Also ideal for soufflés. – If using an older recipe or cookbook, set the oven temperature for Conventional heat 10°C lower than that recommended. The cooking duration does not need to be changed. Top heat –...
"Settings - Language J" message to tell you that: to get back to the correct language. – your appliance is equipped for the Miele|home system. Clock format – your appliance has been successfully set up to use it for the first time.
Before using for the first time ^ Heat the empty oven for at least an Cleaning and heating up for hour. the first time Please ensure the kitchen is well Before use, please remove ventilated during this operation. – any stickers from the oven and Close doors to other rooms to from any accessories.
Operation ^ Select the option you require. Automatic programmes Each Automatic programme has a Your appliance has a wide range of sub-menu with further options which will Automatic programmes to enable you now show in the display. to achieve excellent results with ease.
Manual operation Selecting "Change" brings up all the To operate the oven manually, switch options which can be changed during the appliance on, select the oven the current programme, e.g. the function and temperature, then selected temperature. switch it off again once you have ^ At the end of the cooking finished cooking.
More about manual operation To change the temperature Automatic switch-off can be selected As soon as you have selected a when operating the oven manually. function, the recommended You can also adjust the heat-up temperature with the temperature range phase and the humidity level inside which can be set in brackets beside it the oven.
More about manual operation Entering the Duration, a Start To use Automatic switch-off time or Finish time To switch a programme off automatically select Duration or Finish By entering the Duration, Start time or and enter the time required. Finish time, the cooking process can be programmed to switch off, or on and Example: off, automatically.
More about manual operation Delaying the start with Automatic Sequence of the cooking programme switch-off when using Automatic switch-off The following will appear in the display: We recommend using automatic switching on and off when roasting. Before the programme starts However, do not delay the start for –...
More about manual operation Changing the heating-up After the cooking programme has finished phase – The cooling fan will continue to run With the Fan plus, Auto roast and for a while after the oven has been Conventional heat functions, the switched off to prevent any humidity Heating-up phase will appear with the building up in the oven, on the...
More about manual operation Pre-heating the oven To pre-heat the oven: ^ Select the required function and set Most dishes can be placed in a cold oven. They will then make use of the the temperature. heat produced during the heating ^ Wait for the oven to reach the set phase.
More about manual operation Activating moisture reduction Change function It is a good idea to use this function You can change the function selected when cooking items which are moist on via this option. the inside but which should be crispy The times already entered will be kept.
User programmes The User programmes menu Up to 25 frequently used recipes can be saved under a user-defined name, and If user programmes have already been then called up again as required. created and saved, the following will Either appear: ß...
User programmes To create a User programme After confirming with "Continue", select the name given in the display, or enter If programmes already exist under your own name. To do this: User programmes, the "Create" ^ Use the sensors next to arrows option has to be selected in order to to select a character.
Moisture plus The "Moisture plus" function uses a Please refer to the "Moisture plus" steam injection system. booklet supplied with your oven for Water is taken into the steam injection further information and a selection of system via the tube underneath the recipes.
Moisture plus Automatic programmes Night baking Automatic programmes with Moisture Some of the Automatic programmes for plus set the optimium temperature, the bread and rolls have the option of degree of moisture and also the baking during the night, so that you can duration automatically.
Moisture plus Moisture plus After selecting Moisture plus you need to set the number of bursts of steam. When using the Moisture plus function The options are: you will need to enter ß Automatic – the temperature (at least 130 °C), This requires enough water for one –...
Moisture plus Using Moisture plus The amount of water required will be drawn up into the oven. As the water is ^ Place the food in the oven. taken in, bars will appear in the display. ^ Select Moisture plus The amount of water specified will be more than the amount which is actually ^ Select a temperature.
Moisture plus To evaporate residual moisture The residual moisture evaporation process If there is still water in the steam injection system at the end of a The oven will heat up to approx. programme or if the programme is 150 °C, and the residual water in the cancelled, you will be prompted to oven cavity will evaporate.
Moisture plus Descaling To cancel the residual moisture evaporation process The oven will need to be descaled depending on the number of cooking After the appliance has been switched on, the prompt to evaporate programmes using Moisture plus which residual moisture will appear in the have been run and the amount of water display.
Minute minder (egg timer) The minute minder can be used to time At the end of the time set for the minute any activity in the kitchen, e.g. boiling minder eggs. – the symbol will flash. You can enter a time of up to a –...
Settings Your appliance is supplied with a Currently selected settings are number of standard default settings. indicated by a "L" and without a " " next to them. To change a setting: ^ Select the "Settings J" option. Settings cannot be altered while a cooking programme is in progress.
Settings Time To set the time of day The options are: The time of day is set using either the ß Display numerical keypad or the ß Clock format sensors: ß Set First enter the hours and confirm with "OK". Then enter the minutes and If there is a power cut, the current confirm with "OK".
Settings Main menu Catalyser ß On You can change the order in which options appear in the main menu. Up to (Factory default) three options can be placed at the The catalyser is always switched on. beginning of the main menu (excluding ß...
Settings Cooling fan run-on Pyrolytic ß With reminder The cooling fan will continue to run for a ß A reminder to carry out the pyrolytic while after the oven has been switched off to prevent any humidity building up cleaning process will appear in the in the oven, on the control panel or in display.
Settings Start Display ß Automatic Contrast (Factory default setting) A programme will start automatically The contrast is represented by a bar approx. 20 seconds after making with seven segments. your last entry without having to select Start. Factory default: Four blocked ß...
Settings Volume Keypad tone The volume of the keypad tone, which Buzzer tones bleeps when touched, can be changed or the sound switched off completely. The volume is represented by a bar with seven segments. Factory default: Three blocked Factory default: Three blocked segments.
Settings Safety In operation lock (depending on model) System lock The In operation lock prevents the The system lock prevents the appliance appliance from being switched off being switched on unintentionally, by inadvertently and cooking programmes children for example. from being altered. The system lock has to be set to When the In operation lock has been "Permitted"...
Settings Units Factory default ß All settings Temperature Any settings that you have altered ß °C will be reset to the factory default (Factory default) setting. ß User programmes ß °F All saved user programmes will be deleted. Showroom programme ß...
– solvent-based cleaning agents, discolour. – stainless steel cleaning agents, Clean the front using a damp Miele – dishwasher cleaner, microfibre E-cloth or with a clean – oven sprays, sponge and a solution of hot water and washing-up liquid.
Cleaning and care Accessories FlexiClip telescopic runners Remove all accessories as well as Do not clean FlexiClip telescopic the runners and any extra runners in a dishwasher. This would accessories such as FlexiClip remove the special lubricant. runners from the oven interior before starting the pyrolytic cleaning When cleaning do not use: process.
Cleaning and care Normal soiling Please note: Clean the surfaces using a damp Miele When baking cakes with moist toppings microfibre E-cloth or with a clean or fillings e.g. fruit crumble, be careful sponge and a solution of hot water and not to let them spill over.
Cleaning and care PerfectClean Allow the oven and any The following have been treated with a accessories to cool down before special finish called PerfectClean: cleaning by hand. Danger of burning. – baking tray – universal tray For the optimum performance of PerfectClean, it is important to clean the –...
Page 59
Follow the cleaning effect for up to ten minutes only. instructions given above and do not Miele oven cleaning spray can be left use force to remove them. on for longer. Always follow the instructions on the packaging.
Cleaning and care Oven interior Most cooking residues can be removed with a damp cloth and a mild solution of The oven interior is coated with dark hot water and washing-up liquid. pyrolytic enamel which facilitates cleaning. Never use hard brushes, hard This is a particularly hard enamel with sponges, wire wool pads*, knives or an extremely smooth surface and very...
Page 61
Cleaning and care At the end of the programme it will not Remove any coarse soiling from the be unlocked until the temperature oven before you start. inside the oven has dropped to below 280 °C. Clean the inside of the door (glass). If the pyrolitic cleaning programme has been started by mistake or if the There is a fibre-glass door seal...
Page 62
Cleaning and care After the pyrolytic process any debris The pyrolytic process will be (e.g, ash), can easily be wiped away. cancelled, – if the oven is switched off. Remember to wait until the oven has cooled down before doing so! –...
Cleaning and care To dismantle the oven door The example below is for The oven door is made up of four dismantling a left-hand hinged door. panes of glass and has vents at the top The same instructions apply for a and bottom.
Page 64
^ Pull the middle panes upwards to remove them. ^ Clean the glass panes and other parts with a damp Miele E-cloth or a clean sponge and a solution of hot water with a little washing-up liquid. Wipe dry using a soft cloth.
Page 65
Cleaning and care To reassemble the door: The two middle panes are identical. To ensure that they are refitted correctly, one of the corners is more angled than the others. ^ Fit the second pane in the aluminium trim behind the screw heads. The more angled corner must be positioned at the bottom right-hand side.
Page 66
Cleaning and care The inner door pane must be fitted such that the printed side faces into the door. Before fitting the inner pane the drip channel has to be fitted back onto the pane. When refitting the pane make sure you hold it securely at the top and underneath the drip channel.
Cleaning and care To remove the FlexiClip To remove the side runners telescopic runners Make sure the oven heating elements are switched off and cool. Make sure the oven heating Danger of burning. elements are switched off and cool. Danger of burning. ^ Lift the FlexiClip runner up at the front and pull it out along the rail of the side runner.
Cleaning and care To lower the top heat/grill element Make sure the oven heating elements are switched off and cool. Danger of burning. ^ Remove the runners. ^ Unscrew the wing nut and lower the top heating element. Do not use force to pull it down as this can cause the element to break.
The descaling programme can be run supplied with the appliance. These at any time. have been specially formulated and are available from the Miele Spare However, to ensure the oven functions Parts Department or via the internet correctly you will be automatically on www.miele-shop.com.
Cleaning and care Preparation Start the descaling process. ^ Dissolve one descaling tablet in ^ Select the "Descale" option. approx. 600 ml of cold tap water. ^ Press the OK sensor to start the ^ Place the universal tray on the top suction process.
Page 71
Cleaning and care The steam injection system will need to After the third rinse, residual water will be cleaned at the end of the need to be evaporated from the steam descaling process to remove all traces injection system. of descaling solution. Before proceeding, remove the Prompts to do this will appear in the plastic tube and the container from...
Problem solving guide With the aid of the following guide, minor problems can be easily corrected without contacting Miele. If you cannot resolve a problem following these instructions please contact Miele Service. Do not attempt to open the appliance casing yourself!
Page 73
Problem solving guide Problem Possible cause and remedy ^ Disconnect the appliance from the electricity supply: The top lighting is not working. Switch off and unplug at the socket, or disconnect the fuse, or switch off at the isolator as appropriate. ^ Turn the lamp cover a quarter turn anti-clockwise to release it and then pull it downwards to take it out.
Page 74
– Fault 32: The door has not locked for the pyrolytic cleaning process. Switch the oven off and start the pyrolytic cleaning process again. If the fault code appears again call the Miele Service Department. – Fault 33: The door lock for the pyrolytic cleaning process will not open.
– your Miele Dealer In the UK, your appliance is guaranteed for 2 years from the date of purchase. – Miele (see back cover for contact However, you must activate your cover details). by calling 0845 365 6640 or registering online at www.miele.co.uk.
A range of additional accessories as well as cleaning and care products are available for your Miele oven. Depending on product they are available to order from your Miele Dealer, the Miele Spare Parts Department or via the internet on www.miele-shop.com.
Page 77
Suitable for cleaning surfaces such as stainless steel, glass, plastic and chrome without the use of chemicals. Miele oven cleaner – HUB 5000-XL (internal dimensions: Suitable for removing stubborn soiling. approx. 38 x 35 x 8 cm) It is not necessary to pre-heat the oven beforehand.
(CSA) accessible after the appliance has may be used (available from the been built in. Miele Customer Contact Centre). If the switch is not accessible after installation (depending on country) an additional means of disconnection must be provided for all poles.
Building-in diagrams Dimensions are give in "mm". Appliance dimensions and unit cut-out * Appliances with glass front ** Appliances with metal front...
Installing the oven The appliance must not be The example below is for operated until it has been correctly installing a left-hand hinged oven. installed in its housing unit. Reverse the procedure for a Otherwise it poses an electric shock right-hand hinged oven.
Page 82
Installing the oven Spacers will need to be fitted to the appliance casing depending on the thickness of the housing unit walls: with 16 mm thick housing unit walls with 19 mm thick housing unit walls ^ Open the oven door and secure the oven to the side walls of the housing unit as illustrated.