Page 1
Operating instructions for washing machines To avoid the risk of accidents or damage to the machine, it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr. 11 003 430...
Protective foil and stickers removal ..............18 Miele@home ......................19 1. Set the language ....................20 2. Setting up Miele@home ..................20 3. Set clock format ....................21 4. Remove the transit bars ..................21 5. Commissioning TwinDos ................... 22 6.
Page 3
Water softeners ..................... 63 Dispensing aids ..................... 63 Fabric conditioner and liquid starch ..............63 Miele recommended detergents ................65 Recommended detergents in accordance with Directive (EU) Nr. 1015/2010..66 Cleaning and care .................... 67 Cleaning the external casing and the control panel ..........67 Cleaning the detergent dispenser drawer .............
Page 4
Contents Problem solving guide .................. 71 The programme does not start................71 Fault message after a programme has been interrupted........72 Fault message at the end of a programme ............73 Messages or faults with the TwinDos system ............75 Problems with TwinDos ..................
/ recycling centre for electrical and electronic ap- pliances, or contact your dealer or Miele for advice. You are also respons- ible (by law, depending on country) for deleting any personal data that may be stored on the appliance being disposed of.
It must be used only as a domestic appliance to wash items which are specified by the manufacturer as being washable on the wash care label. Miele cannot be held liable for damage resulting from in- correct or improper use or operation.
Page 8
Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from the wash- ing machine unless they are constantly supervised. Children 8 years and older may only use the washing machine un- supervised if they have been shown how to use it safely and recog- nise and understand the consequences of incorrect operation.
Page 9
Faulty components must only be replaced by genuine Miele ori- ginal spare parts. Only when these parts are fitted can Miele guaran- tee the safety standards of the machine. The electrical socket must be easily accessible after installation so that the machine can be disconnected from the electricity supply if necessary.
Page 10
This special lamp must only be used for the purpose it is intended for. It is not suitable for room lighting. Replacement lamps may only be fitted by a Miele au- thorised person or the Miele Service Department.
Page 11
Warning and Safety instructions Correct use Do not install the washing machine in a room where there is a risk of frost. Frozen hoses may burst or split. The reliability of the elec- tronic control unit may be impaired at temperatures below freezing point.
Page 12
If, however, you do wish to descale it, only use a proprietary natural citric acid based descaling agent. Miele recommends using Miele descaling agent which is available to order online at www.miele.co.uk or from Miele. Strictly observe the instructions on the packaging.
Page 13
A Miele tumble dryer can be stacked on top of a Miele washing machine using the appropriate stacking kit (available as an optional accessory). Please make sure you order the correct one for the Miele washing machine and Miele tumble dryer.
Operating the washing machine Control panel a Sensor To go back a level in a menu. b Touch display c Start/Stop sensor Touching the Start/Stop sensor starts the selected programme or cancels a programme that has already been started. The sensor flashes slowly as soon as it is possible for a programme to be started and then lights up constantly after the programme has started.
MobileControl turn to the main menu. Values set pre- With MobileControl you can operate your viously are not saved. washing machine remotely with the Miele@mobile app. 11:02 The Remote control setting must be ...
Operating the washing machine Extras menu (multiple choice) Examples on how to operate the machine Extras 11:02 Option lists Quick Water plus Programme menu (single option list) 11:02 Programmes Extra rinse Cottons Minimum iron ...
Page 17
Operating the washing machine Setting numerical values Pull-down menu You can set numerical values in some The pull-down menu can be used to menus. display information, e.g. about a wash programme. Clock display Overview 11:02 Temperature Spin speed ...
Before using for the first time Remove the detergent cart- Damage resulting from incorrect ridges and the drain hose el- installation and connection. bow from the drum Installing and connecting the wash- ing machine incorrectly will cause Two detergent cartridges for automatic serious property damage.
Store™. In order to use it you need: – a WiFi network – the Miele@mobile App – a Miele user account. The user ac- count can be created via the Miele@mobile App. The Miele@mobile App will guide you as you connect your washing machine to your home WiFi network.
6 steps of the initial commissioning process. Skip Continue 1. Set the language To set up Miele@home now: Touch You will be asked to select the language Continue sensor. you require for the display. It is possible Tip: To postpone setup until later:...
Before using for the first time 3. Set clock format 4. Remove the transit bars The time of day display can be in 12- or Damage resulting from failure to 24-h clock format. remove the transit bars. Select the clock format you want and Failure to remove the transit bars can confirm this with the OK sensor.
Confirm the pre-set value with the OK Settings for compartment sensor, or change the value. The procedure below describes the pro- UltraPhase 1 cedure for Miele UltraPhase 1 and Miele UltraPhase 2. The procedure for other Hardness level I 48 ml detergents is similar.
Page 23
Before using for the first time Remove the foil or the stopper from Push the UltraPhase 1 detergent the detergent cartridge. cartridge into compartment 1 until it locks into position. The following message appears in the display: Now enter the settings for UltraPhase 2 ...
Page 24
Before using for the first time Settings for compartment The dispensing quantity for UltraPhase 2 is pre-set for (hard- ness level II). Dosage for comp. 11:02 Push the UltraPhase 2 detergent cartridge into compartment 2 until it Confirm the pre-set value with the OK locks into position.
Before using for the first time 6. Start the calibration pro- gramme For optimum water and energy con- sumption and excellent wash results, it is important to calibrate the washing machine. To do this, the Cottons programme must be run without laundry. No other programmes can be started until calibration has been carried out.
– Washing at low temperatures and/or using liquid detergents can cause bacteria and odours to build up in the washing machine. Miele therefore re- commends cleaning the washing ma- chine once every month. The washing machine reminds you to...
Washing environmentally and economically 2. Actual consumption EcoFeedback You can view information about the en- You can view the actual amount of en- ergy and water consumption of your ergy and water used by a programme washing machine with the pull-down both during and at the end of the pro- menu.
1. Prepare the laundry Tip: Stains (e.g. blood, egg, coffee, tea) can be pre-treated using some handy tricks which can be found in the Miele guide to laundry care. Damage due to solvent-based cleaning agents Cleaning agents containing benzine, stain remover, etc., can damage...
2. Select a programme Switching on the washing ma- Selecting a programme chine Touch the Programmes sensor. Press the control. 11:02 Programmes The interior drum lighting will come on. Cottons Minimum iron 2:39 1:59 The drum lighting will go out automat- ically after 5 minutes.
3. Select programme settings 2. Select the detergent Selecting the temperature When using Miele's 2-phase system You can alter the preset temperature you must set the colour of the laundry. of a wash programme. Select Whites for loads of white items, ...
Page 31
3. Select programme settings Selecting Extras Stains You can supplement the wash pro- In order to clean stained laundry more grammes with extra options. effectively, you can choose from a list of various types of stains. The wash Touch the Extras sensor.
4. Load the washing machine Open the door Close the door Take hold of the door and pull it Make sure that no items are caught open. between the door and the seal. Check the drum for pets or foreign objects before loading it with laun- dry.
UltraPhase 1 and UltraPhase 2 clean white and coloured fabrics thoroughly. UltraPhase 1 and UltraPhase 2 single- use cartridges are available to order from Miele, your Miele dealer or via the Miele online shop. Press the yellow button above the cartridge to release the lock.
Page 34
5. Add detergent Level of soiling Using other methods to remove stains The level of soiling in laundry is split into three settings: If you wish to use additional methods of stain removal, you have the following – Light options: No visible soiling or stains –...
5. Add detergent Adding detergent Detergent dispenser drawer Any detergent suitable for automatic front loading washing machines can be used. Please observe the instructions for use and dosage on the detergent packaging. Ensure that TwinDos dispensing is deactivated. Add detergent in accordance with the value in the pull-down dosage display.
Page 36
5. Add detergent Adding fabric conditioner Tips on dosing Adjust the detergent dosage to the level of soiling of the laundry and the size of the load. Too little detergent: – Results in laundry not being cleaned properly and may cause it to become grey and hard to the touch over time.
Each capsule contains the correct amount for one wash cycle. Caps are available to order from Miele or from the Miele online shop (see the end of this booklet for contact details). Capsules pose a health risk.
Page 38
5. Add detergent The wash programme will dispense the contents of the capsule at the correct time. Water intake to the compartment is solely via the capsule. Do not add any additional fabric con- ditioner to the compartment. Remove the empty capsule at the end of the programme.
6. Start the programme - the end of a programme Pull open the door. Starting a programme Remove the laundry. The programme can be started when the Start/Stop sensor is flashing on and Items left in the drum could discolour off.
Spinning Final spin speed in the pro- Programme gramme Cottons 1600 Cottons When a programme is selected, the op- 1600 timum spin speed for this wash pro- Minimum iron 1200 gramme is shown in the display. Delicates A faster spin speed can be selected for QuickPower wash 1600 certain wash programmes.
Spinning Omitting the final spin (Rinse Interim spin hold) There is a spin cycle after the main wash and between the rinses. A reduc- If Rinse hold is selected, the laundry re- tion in the final spin speed will also re- mains in the water following the final duce the interim spin speed as appro- rinse cycle.
Programme chart Cottons cold to 90 °C Max. load 9.0 kg Use for Cotton, linen or mixed fibre fabric, e.g. table linen, towelling, under- wear, T-shirts etc. Notes – The Cottons 60°/40 °C programme has a shorter programme dura- tion, longer temperature holding times and higher energy con- sumption than the Cottons /...
Page 43
Programme chart QuickPower wash 60 °C – 40 °C Max. load 5.0 kg Use for Normally soiled garments which are also suitable for washing in the Cottons programme. Note – A special saturation process and wash rhythm ensure that the laundry is cleaned particularly quickly and thoroughly. Automatic plus Cold to 40 °C Max.
Page 44
Programme chart Shirts Cold to 60 °C Max. load 1.0 kg/2.0 kg Use for Shirts and blouses made of cotton and mixed fibre. Notes – Pre-treat collars and cuffs if necessary. – Wash silk shirts and blouses in the Silks programme. – If the preset Pre-ironing option is switched off, the maximum load capacity is increased to 2.0 kg.
Page 45
Programme chart Outerwear Cold to 40 °C Max. load 2.5 kg Use for Performance outerwear (e.g. jackets and trousers) made from mem- brane fabric such as Gore-Tex®, SYMPATEX®, WINDSTOPPER® etc. Notes – Zip up or close jackets before washing. – Do not use fabric conditioner. –...
Page 46
Programme chart Down duvets cold to 60 °C Max. load 2.5 kg 1 down duvet 2.20 m x 2.00 m Use for Quilts, duvets and pillows with feather or down filling. Notes – Remove air from the items before washing to prevent an excessive build-up of foam.
Page 47
Programme chart Curtains Cold to 40 °C Max. load 2.0 kg Use for Curtains specified as machine-washable by the manufacturer. – To remove dust, the Pre-wash Extra is selected automatically. – For curtains which crease easily, reduce the spin speed or deselect the spin.
Page 48
Programme chart Freshen up Max. load 1.0 kg Use for Dry, clean cotton, linen or mixed fibre garments which are slightly creased. The garments must be suitable for drying in a tumble dryer and suitable for ironing . Notes –...
Page 49
Cleaning the washing machine will significantly reduce bacteria, mould, and biofilm and prevent the build-up of unpleasant odours. Notes – Optimum results can be achieved by using Miele machine cleaner. Alternatively, a universal powder detergent can be used. – Dispense the washing machine cleaner or universal detergent dir- ectly in the drum.
Extra options You can use the extra options buttons SingleWash to augment the wash programmes. For efficiently washing a very small load (< 1 kg) in a normal wash programme. Quick The wash duration is reduced. The programme duration is reduced. Please note the following advice: Mechanical action and energy usage are increased.
Extra options Soak Extra quiet For heavily soiled and stained items This option reduces noise levels during with protein stains. the wash programme. Use this if you want to wash during quiet periods (for A duration of between 30 minutes and 6 instance when children are sleeping).
Page 55
Programme sequence Special features in the pro- = low water level gramme sequence = medium water level Anti-crease: = high water level at the end of the programme the drum = intensive rhythm continues to turn at intervals for up to 30 minutes to help prevent creasing.
PowerWash 2.0 lower than 600 rpm. PowerWash 2.0, a washing technique – CapDosing (, ) has not been se- developed by Miele, is activated in the lected for the main wash. following programmes with small and medium-sized loads: With some options (e.g. Pre-wash, –...
Changing the programme sequence Cancelling a programme Changing a programme You can cancel a wash programme at After the successful start of a pro- any time after it has started. gramme it is no longer possible to change the programme. ...
Garment care label symbols Drying Washing The number of dots indicates the dry- The figure quoted in the bucket is the ing temperature maximum temperature the garment can be washed at. The number of Normal temperature bars under the symbol indicates the ...
Favourite programmes To create a favourite pro- To enter a name gramme It is best to select short, memorable names. You can save your own customised wash programmes under names of your Touch the letters or characters you choice. want.
Washing assistant The wash assistant helps you with loads consisting of items with different care instructions. The washing machine will use the list of items to put together a suitable wash programme. Scroll to the second page in the main menu.
Timer The Timer can be used to set the time Deleting the timer you wish a programme to finish or start The selected time for the timer can be at. The programme start can be delayed changed before the programme starts. by up to 24 hours.
Timer Setting the timeframe SmartStart If you have activated the SmartGrid The SmartStart function lets you function in Settings, SmartStart by define a period of time during which will appear in the display SmartFinish by your washing machine will start auto- instead of Start at Finish at...
Detergent The correct detergent Dispensing aids All detergents produced for automatic Use dispensing aids, (e.g. balls) if these washing machines are suitable. Follow are supplied with the detergent, particu- the manufacturer's instructions and larly when using liquid detergent. dosage recommendations on the pack- Refill packs of detergent aging.
Page 64
Detergent TwinDos dispensing Adding fabric conditioner or li- quid starch separately One of the automatic dispensing con- tainers must be filled with fabric condi- Prepare the starch in accordance with tioner. the manufacturer's instructions on the packaging. Select the programme.
Detergent Miele recommended detergents Miele detergents and care products have been specially designed for Miele wash- ing machines. They are available to order via the internet at www.miele.co.uk or from Miele. Miele Miele Miele Miele Cap Cap Cap ...
Detergent Recommended detergents in accordance with Directive (EU) Nr. 1015/2010 The recommendations apply to the temperature ranges given in the Programme chart. Universal Coloureds Delicates and Specialist woollens detergent Cottons – – Minimum iron – – – ...
Cleaning and care Cleaning the external casing Cleaning the detergent dis- and the control panel penser drawer Washing at low temperatures and the Risk of electric shock! use of liquid detergent can lead to a Mains voltage is present when the build-up of bacteria in the detergent washing machine is switched off dispenser drawer.
Page 68
Cleaning and care Cleaning the siphon and the / compartment channel Liquid starch results in clogging. If clogged, the siphon in the / compartment will not work and the compartment can overflow. Clean the siphon particularly thor- oughly after using liquid starch a few times.
To clean the system, you either need a “TwinDosCare” cleaning cartridge (only available in selected countries) or an empty TwinDos container. Both are available from the Miele online shop. The washing machine has a cleaning programme for the TwinDos system. Running the cleaning programme will clean the hoses inside the washing ma- chine.
Cleaning and care First turn off the stopcock. Cleaning the water inlet filter Unscrew the inlet hose from the stop- The washing machine has a filter to pro- cock. tect the water inlet valve. The access- ible filter in the union at the open end of the inlet hose should be checked every six months or so, or more often if there are frequent interruptions to the water...
The door is not closed properly. The door lock could in the display: not engage. The door will not lock. Call Close the door again. Service. Start the programme again. If the fault message appears again, contact Miele.
Wait at least 2 minutes before reconnecting the washing machine to the mains electricity supply. Then switch the washing machine on again. Restart the programme. If the fault message appears again, contact Miele. The water protection system has reacted. Waterproof system ...
In order to prevent bacteria and unpleasant odours run the "Clean ma- chine" programme. building up in the washing machine, run the Main- tenance wash programme using Miele machine cleaner or a universal powder detergent. The water inlet for hot water is blocked or turned off. ...
Page 74
Remove the fluff with your finger. Do not use any sharp or pointed tools to do this. Restart the programme after cleaning. If the fault message appears again, contact Miele. The washing machine can still be used but with re- duced functionality.
Problem solving guide Messages or faults with the TwinDos system Problem Cause and remedy The detergent in the cartridge is running low. There is Only a few more sufficient left for approx. 4 to 8 wash programmes. washes are possible ...
Touch the sensor before running the next TwinDos dispensed. programme. Automatic dispensing will be activated. No detergent/fabric softener was dispensed although automatic dispensing was activated. Try again. If detergent is still not dispensed, call Miele.
In order to prevent bacteria and unpleasant odours building up in the washing machine, run the Main- tenance wash programme using Miele machine cleaner or a universal powder detergent. The door and the detergent dispenser drawer were left open after washing.
Page 78
Problem solving guide General problems with the washing machine Problem Cause and remedy Large amounts of deter- The water pressure is too low. gent residue remain in Clean the water inlet filter. the detergent dispenser It may be useful to select the Water plus extra op- drawer.
Page 79
Problem solving guide General problems with the washing machine Problem Cause and remedy The display is dark. The display has switched off automatically to save energy (Standby mode). Press a button. Standby comes to an end. Steam comes out of the This is not a fault.
They do not remove fruit, coffee and tea result. stains. Use the Miele 2 Phase System. The targeted addi- tion of UltraPhase 2 during the wash process re- moves stains effectively. Use a general purpose powder detergent contain- ing a bleaching agent.
Problem solving guide The door will not open Problem Cause and remedy The door cannot be The door is locked during a programme. pulled open during a Touch the Start/Stop sensor to cancel the pro- programme. gramme. The programme is cancelled, the door will unlock and you will be able to pull it open.
Problem solving guide Draining the washing machine Opening the door in the event of a blocked drain outlet and/ Remove the drain filter, though not or power cut completely. Switch off the washing machine. Place a suitable container under the access panel, e.g.
Page 83
Problem solving guide Open the door Danger of injury due to rotating drum! Reaching into a moving drum is ex- tremely dangerous. Always make sure that the drum is stationary before reaching in to re- move laundry. Clean the drain filters thoroughly. ...
Optional spare parts and accessories cannot remedy yourself, please contact for this washing machine are available your Miele Dealer or Miele Service. from your Miele Dealer, the Miele Spare Parts Department or via the internet at Contact information for Miele Service www.miele.co.uk.
Installation and connection Front view a Water intake hose with Waterproof f Door system for alternative water sup- g Access to filters, pumps and emer- plies. gency release b Mains connection cable h Access panel for TwinDos cartridges c Flexible drain hose (with detachable i Four height-adjustable feet swivel elbow) d Control panel...
Installation and connection Rear view a Drain hose f Water intake hose with Waterproof system for alternative water sup- b Transport clips for inlet and drain plies. hoses and mains connection cable g Safety caps for transit bars c Mains connection cable h Transport clips for inlet and drain d Protruding lid for holding when mov- hoses and for storing transit bars...
2. then use a screwdriver to release the Secure the washing machine using a catches at the top and bottom. clamp/fastening bracket (MTS floor mounting kit – available from your Miele dealer or Miele spare parts de- partment).
Page 88
Installation and connection Using the spanner supplied, turn the Turn the right-hand transit bar 90°, left-hand transit bar 90°, then then withdraw the transit bar. withdraw the transit bar.
Installation and connection Risk of injury from sharp edges. There is a risk of injury from reaching into holes that are not covered. Cover the holes for the transit bars after they have been removed. Secure the transit bars to the back of the washing machine.
Installation and connection Levelling the machine The washing machine must stand per- fectly level on all four feet to ensure safe and proper operation. Incorrect installation may increase elec- tricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet are used for levelling the washing machine.
Installation and connection Installing under a continuous work- Washer-dryer stack The washing machine can be combined with a Miele tumble dryer in a washer- Risk of electric shock due to ex- dryer stack. The appropriate “WTV” posed cables stacking kit* to match your dryer is re- There is a risk of coming into contact quired.
The inlet hoses The water protection system – The casing on the inlet hoses con- The Miele water protection system pro- tains two solenoid valves , which tects all parts of the washing machine cut off the water intake directly at the from water damage.
Page 93
Installation and connection The electronic unit and drainage and overflow protection – Drainage protection Any leaking water is collected in the sump in the base of the machine. A float switch closes the solenoid valves , preventing any more water from flowing into the machine and water in the suds container is pumped away.
Installation and connection The washing machine should be con- Connection to the water supply nected to a mains water supply in ac- Risk of electric shock! cordance with current local and national safety regulations. The German author- There are electrical wires in the water ities do not require it to have a non-re- inlet hose.
Hose extension Always connect the washing ma- A 1.5 metre long (metal) extension hose chine to cold mains water. is available from your Miele dealer or the Miele Spare Parts Department as an Markings on the water intake hoses optional extra.
Page 96
Installation and connection Cold water (default setting) Soft water, rain water and well water The washing machine will be operated 1. For hygiene reasons water should be with cold mains water only. at least of the quality used for bathing in. The other intake hose is secured to the back of the washing machine.
Page 97
Installation and connection Water intake overview depending on selection programmed Main wash Rinses First and sub- Final rinse sequent rinses Cold water / Hot main wash / / Hot main wash + rinses ...
If required, the hose can be extended to a length of up to 5 m. Accessories are available from Miele or from your Miele dealer. For a delivery head of more than 1 m (up to a max. of 1.8 m) a replacement drain pump will need to be fitted.
If the connection cable is damaged, it must only be replaced with a specific connection cable of the same type (available from Miele). For safety reas- ons, such replacement may only be carried out by a qualified technician or Miele Service.
Technical data Height 850 mm Width 596 mm Depth 643 mm Depth with door open 1077 mm Height for building under 850 mm Width for building under 600 mm Weight Approx. 96 kg Capacity 9 kg dry laundry Voltage See data plate Connected load See data plate Fuse rating...
Technical data Conformity declaration Miele hereby declares that this washing machine complies with Directive 2014/53/ The complete text of the EU declaration of conformity is available from one of the following internet addresses: – Products, Download from www.miele.co.uk – For service, information, operating instructions etc: go to www.miele.co.uk/do- mestic/customer-information-385.htm and enter the name of the product or the...
Technical data Data sheet household washing machines In acc. with delegated regulation (EU) No. 1061/2010 MIELE Model name/identifier WWV 980 WPS Passion 9,0 kg Rated capacity Energy efficiency class A+++ (most efficient) to D (least efficient) A+++ 109 kWh/year Annual energy consumption (AE Energy consumption of the standard “60°C cotton programme”...
Page 103
Technical data Based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used. Based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load.
Consumption data Load Consumption data Energy Water Duration Residual in kWh in l moisture Cottons 90 °C 2.60 2:29 60 °C 1.45 2:29 60 °C 1.10 2:19 * 0.60 2:59 * 0.43 2:59 40 °C 1.20 2:39 * 0.35 2:59 20 °C 0.45 2:39 Minimum iron 30 °C 0.60 1:59...
Consumption data Note for test institutes Test programme in accordance with EN 60456 and energy label with Directive 1061/2010 Consumption data can vary from the nominal values given depending on water pressure, water hardness, water inlet temperature, room temperature, type and volume of load, fluctuations in the electricity supply and any extras selected.
Settings Changing a setting You can use the settings to alter the washing machine's electronics to suit Change the value displayed and con- changing requirements. firm with OK. The settings can be altered at any time. Touch an option to select it. Accessing the settings menu An option which is selected will be highlighted orange.
In this setting you can check the If wished, you can set a different saved energy and water consumption three-digit code. values and enter the energy cost. If you forget the code, only Miele Options Technical Service can unlock the washing machine. –...
Settings Memory Display brightness The washing machine will save the The brightness of the display can be last settings (temperature, spin speed altered. and some of the Extras) selected for a It can be set to one of 7 different set- programme after the programme has tings.
Heavy leted. The Factory default setting is: Normal The following agents can be used: Water plus level – Miele UltraPhase 1 – Miele UltraPhase 2 There are four different water levels which can be selected for the Water – Universal detergent plus Extra.
Settings Maximum rinse level Gentle action The water level in the rinses can be With gentle action activated, drum permanently set to the highest value. agitation is reduced. In this way, lightly soiled items can be washed more This function is important for allergy gently.
– The WiFi connection will be reset to The WiFi function is reactivated. the factory setting. Deactivate Miele@home is no longer set up. A new (visible if Miele@home is activated) connection setup has to be carried out in order to use the Miele@home setting Miele@home remains set up, the WiFi again.
This function can be used for starting Once the Miele@mobile app has been your washing machine automatically installed on your mobile device, you at a time when your energy supplier's can check the status of your washing energy costs are most economical.
RemoteUpdate. Other- connected to a WLAN network and you wise, the RemoteUpdate will be have an account in the Miele@mobile aborted and will not be installed. app. The washing machine must be re- gistered with your account in the app.
Settings – Rain water Appliance parameters This setting is recommended if the Water intake water hardness level of the alternative water supply is lower than that of the You can programme 6 options for the mains water supply. Detergent sav- water intake.
Temperature reduction Installation requirements At high altitudes water has a lower Low water pressure boiling point. Miele recommends ac- If the water pressure is below 100 kPa tivating the reduced temperature set- (1 bar), the programme will be can- ting at altitudes of 2000 m or above to celled and a fault message will appear.
– Multi-purpose powder detergent this washing machine. All the products – For white and light-coloured laundry have been designed for Miele washing as well as heavily soiled cotton items machines. – Effective stain removal even at low...
Optional accessories WoolCare Specialist detergents – Liquid detergent for woollens and Specialist detergents are available as delicates capsules in convenient single dose amounts or in a handy bottle. – Includes a special wheat protein con- ditioning formula Outerwear – Helps prevent felting –...
Optional accessories Descaling agent Additive – removes heavy limescale deposits Booster – Mild and gentle with natural citric – For removing stains acid – For white and coloured laundry Water softener tablets – Available as capsules in conveni- – Reduces the amount of detergent ent single dose amounts needed for hard water Machine care...