Sony BVP-E30 Maintenance Manual
Color video camera
Hide thumbs
Also See for BVP-E30:
- Operation manual (38 pages) ,
- Manual (34 pages) ,
- Brochure & specs (14 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Sony BVP-E30
Summary of Contents for Sony BVP-E30
- Page 1 COLOR VIDEO CAMERA BVP-E30 BVP-E30P BVP-E30WS BVP-E30WSP MAINTENANCE MANUAL Volume 1 1st Edition Serial No. 100001 and Higher: BVP-E30 Serial No. 400001 and Higher: BVP-E30P Serial No. 100001 and Higher: BVP-E30WS Serial No. 400001 and Higher: BVP-E30WSP...
-
Page 2: Bvp-E30/E30P M-V1
Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. Gooi de batterij niet weg. maar lever hem in als KCA. Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA. BVP-E30/E30P M-V1... -
Page 3: Bvp-E30/E30P M-V1
Hävitä käytetty paristo valmistajan ohjeiden Remplacer uniquement avec une batterie du même mukaisesti. type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. 1 (P) BVP-E30/E30P M-V1... -
Page 4: Bvp-E30/E30P M-V1
For more information regarding recycling of re- chargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/ Caution: Do not handle damaged or leaking Lithium-Ion batteries. 2 (P) BVP-E30/E30P M-V1... -
Page 5: Table Of Contents
1-11. Upgrading the Software ..............1-17 (E) 1-11-1. Upgrading MAIN Program ..........1-17 (E) 1-11-2. Upgrading BOOT Program ..........1-17 (E) 1-12. Setting Scene File Number ..............1-18 (E) 1-13. Removing and Reinstalling the Flexible Card Wires ......1-19 (E) 1 (E) BVP-E30/E30P M-V1... -
Page 6: Bvp-E30/E30P M-V1
3-3. OPERATION Menu ................3-4 (E) 3-4. PAINT Menu ..................3-13 (E) 3-5. MAINTENANCE Menu ..............3-26 (E) 3-6. FILE Menu ..................3-35 (E) 3-7. DIAGNOSIS Menu ................3-40 (E) 3-8. SERVICE Menu .................. 3-40 (E) 2 (E) BVP-E30/E30P M-V1... -
Page 7: Bvp-E30/E30P M-V1
5-5. RPN Pixel Concealment ..............5-14 (E) 5-6. RPN Compensation Adjustment ............5-15 (E) 5-7. White Vertical Line Compensation ............. 5-16 (E) 5-8. V-SUB Voltage Adjustment ............... 5-17 (E) 5-9. V-REG Voltage Adjustment ............... 5-18 (E) 3 (E) BVP-E30/E30P M-V1... -
Page 9: Manual Structure
Manual Structure Purpose of this manual This manual is the maintenance manual volume 1 of Color Video Camera BVP-E30/ E30P/E30WS/E30WSP. This manual is intended for use by trained system and service engineers, and is provided information that is premised parts levels service for this unit. -
Page 10: Contents
Section 3 Setup Menu Describes the setup menu, etc. Section 4 File System Describes the file structure, etc. Section 5 Electrical Alignment Describes electrical adjustment necessary for maintenance of the unit or replacement of parts. 6 (E) BVP-E30/E30P M-V1... -
Page 11: Service Overview
When using the file data stored in the memory stick or the IC memory card (for MSU), make sure that the file data for BVP-E10 series or BVP-E30 series are stored. (For details on the file system, refer to Section 4.) -
Page 12: Description On Backup Battery
The lithium battery is critical part to safe operation. Components marked ! are critical to safe operation. Replace the component with Sony part whose part number appears in the manual published by Sony. Therefore, specified parts should be used in the case of If the component is replaced by any part other than the replacement. -
Page 13: Connector Input/Output Signals
By controlling the voltage at pin 5 during operation, L: 0V switching between the decoded return video signal and SER DATA IN H: +5V L: 0V the camera component signal is done in the viewfinder. H: Camera, L: Return video 1-3 (E) BVP-E30/E30P M-V1... -
Page 14: Bvp-E30/E30P M-V1
5 V p-p COM DATA OUT 5 V p-p IIC CLOCK OUT (CA) 5 V p-p IIC DATA IN/OUT (CA) 5 V p-p, 4700 Z, Pull up No connection No connection (0 dBu = 0.775 Vrms) 1-4 (E) BVP-E30/E30P M-V1... -
Page 15: Bvp-E30/E30P M-V1
Note 4 : Specifications of TAPE REM Signal Tape Remaining (VTR) Input Signal at Pin 25 Remark TAPE1 TAPE2 +5 V +5 V +3.4 V +5 V +3.1 V G TALLY lamp lights at +3.1 V +5 V +2.2 V 1-5 (E) BVP-E30/E30P M-V1... -
Page 16: Bvp-E30/E30P M-V1
No connection No connection No connection No connection No connection No connection No connection No connection No connection No connection (Reserve) (Reserve) 18 MHz OUT (G) GND for 18 MHz 18 MHz OUT (X) 3.3 V p-p 1-6 (E) BVP-E30/E30P M-V1... -
Page 17: Connection Connector
1-4. Function of Internal Switches Ref. No. Designation Description Factory setting MIC +48 V MIC POWER +48 V ON/OFF switch Set to OFF when using the microphone of the internal batteries type. MB-953 board (B side) 1-7 (E) BVP-E30/E30P M-V1... -
Page 18: Bvp-E30/E30P M-V1
4:3/16:9 Set corresponding to the camera to be used. BVP-E30/E30P: BVP-E30WS/E30WSP: 16:9 S1-2 PAL/NTSC Set corresponding to the camera to be used. BVP-E30/E30WS: NTSC BVP-E30P/E30WSP: S101 16:9 NTSC NR-72 board (B side) TG-229 board (B side) 1-8 (E) BVP-E30/E30P M-V1... -
Page 19: Remove And Installation Of Exterior Parts
1-6. Location of Printed Wiring Boards MB-953 SW-1075 SW-1071 SE-767 CN-2209 (BVP-E30P only) CN-2204 TG-229 PA-273 NR-72 DPR-261 DC-DC CONVERTER (RE-201 board) CN-2210 CN-2206 CN-2208 AT-148 CN-2205 IF-969 CN-2207 VA-226 DR-536 SW-1067 (BVP-E30/E30WS/ E30WSP only) PA-272 SW-1068 SW-1069 PA-274 SW-1070 1-9 (E) BVP-E30/E30P M-V1... -
Page 20: Circuit Description
Various CCD drive conditions, adjustment data (V-sub BVP-E30/E30WS/E30WSP, the other is for one filter voltage, RG voltage, black/white shading, etc.) are written type without a servomotor used in the BVP-E30P. -
Page 21: Video Signal System (Va-226 Board, Dpr-261 Board, And If-969 Board)
IC501, the VBS/SC by IC502, the Y/R-Y/B-Y signal for VF by IC503, and the TEST signal by IC800. The DPR-261 board, also control PLL and H-Phase/SC- Phase at genlock and generates various timing pulses such as HD/VD/SYNC. 1-11 (E) BVP-E30/E30P M-V1... -
Page 22: System Control (At-148 Board)
When a white/black VF is connected, the VF-Y signal input from the DPR-261 board are mixed with the cursor, marker and character signals in the different block to the COLOR VF signal and then output to VF VIDEO OUT as a monochrome VF signal. 1-12 (E) BVP-E30/E30P M-V1... -
Page 23: Power Supply Block (Dc-Dc Converter) (Re-201 Board)
An overvoltage detection circuit is equipped only for the +1.4 V output. When the +1.4 V output exceeds +2.0 V under abnor- mal conditions, the outputs of all voltages are stopped by the L_SHUTDOWN signal like the output short-circuit protection circuit. 1-13 (E) BVP-E30/E30P M-V1... -
Page 24: Diagnosis
About mark 8 CA, is as described below according to the type of CA connected to the camera. Refer to the maintenance manual supplied with the camera adaptor. CA-570 CA-550 MD:-- MD:-- AU:-- AU:-- TR:-- TR:-- CA-530 CA-950 VSE:-- DA :-- DVP:-- IF :-- DC :-- AU :-- SDI:-- DPR:-- TX :-- 1-14 (E) BVP-E30/E30P M-V1... -
Page 25: Contents Of The Eeprom And Fram Data
(D-12/A side) VA-226 board *1: IC8 on the PA-272 board cannot be replaced because the data cannot be re-set. When IC needs to be replaced due to defective IC, contact your local Sony Sales Office/Service Center. 1-15 (E) BVP-E30/E30P M-V1... -
Page 26: Adjustment And Setting Items After Replacement Of Board
Referring to Section 1-4, set the internal switch. . Reset the reference file, operator file and scene file. (Refer to Section 4.) . Replace lithium battery on the AT-148 board with a new one, and reset date. (Refer to Sections 1-1-5 and 3-5.) 1-16 (E) BVP-E30/E30P M-V1... -
Page 27: Upgrading Main Program
5. Restart the unit, and confirm the version indication using DIAGNOSIS menu. When the tally switch on the camera adaptor is set to ON, the tally lamp will blink during being upgrading, and then light up when upgrading is completed. 1-17 (E) BVP-E30/E30P M-V1... -
Page 28: Setting Scene File Number
Change the scene file number using the SETUP page in the SERVICE menu. Refer to Section 5-1-6 to display of the SERVICE menu. Menu setting: MENU: SERVICE PAGE: SETUP ITEM: SCENE FILE TYPE → 5 or 32 1-18 (E) BVP-E30/E30P M-V1... -
Page 29: Removing And Reinstalling The Flexible Card Wires
1. Hold the flexible card wire with its blue surface facing to the front, and insert it in the direction of arrow A. 2. Close the connector latch in the direction of arrow B to lock it. Flexible card wire Connector latch Blue surface Connector 1-19 (E) BVP-E30/E30P M-V1... -
Page 30: How To Extend The Circuit Board
DPR-261 board extension assembly. CN3 on the EX-878 board. CN10/MB-953 board CN13 MB-953 board EX-878 board EX-884 board side B2.6 x 5 EX-885 board side DPR-261 board DC-DC converter extension assembly DPR-261 B2.6 x 5 board 1-20 (E) BVP-E30/E30P M-V1... -
Page 31: Extending The Ccd Block
Return the NR-72 board to the normal position. MB-953 board NR-72 board MB-953 board B2.6 x 4 EX Harness CCD block Flexible card wires 5. Return the DPR-261 board to the normal position. (140 mm) 1-21 (E) BVP-E30/E30P M-V1... -
Page 32: Inspection And Maintenance
Sony P/N Remarks PAD ASSY A-8279-977-X rubber RET SW COVER ASSY X-3608-852-X rubber FILTER UNIT, OPTICAL 1-547-579-2X for BVP-E30 FILTER UNIT, OPTICAL 1-758-002-1X for BVP-E30P FILTER UNIT, OPTICAL 1-467-820-2X for BVP-E30WS FILTER UNIT, OPTICAL 1-467-820-1X for BVP-E30WSP BATTERY, LITHIUM CR-2032... -
Page 33: Bvp-E30/E30P M-V1
1-23 (E) BVP-E30/E30P M-V1... -
Page 34: Cares After Using Under Special Environment
If the unit is not taken care of appropriately, corrosion may occur inside that may cause fire and electric shock. 4. Clean out the contacting surface of connectors. 5. Perform the general operational check and confirm that the unit operates correctly without any abnormality. 1-24 (E) BVP-E30/E30P M-V1... -
Page 35: Fixtures
Hexagonal bit To tighten screw J-6325-400-A Torque screwdriver (3 kg) 7-700-736-05 Hexagon wrench (d = 1.5 mm) To remove screw 7-700-736-06 Hexagon wrench (d = 0.89 mm) Memory stick (commercially available) To store the camera settings 1-25 (E) BVP-E30/E30P M-V1... -
Page 37: Replacement Of Main Parts
Filter disk unit and the DR-536 board are not attached to This shortens the wire life. CCD unit for repair of the BVP-E30/E30WS/E30WSP. Install the removed filter disk unit into a new CCD unit. 4. Remove the four screws with stopper, and remove the CCD block. -
Page 38: Bvp-E30/E30P M-V1
5. BVP-E30/E30WS/E30WSP 6. Remove the four screws, and remove the front panel. Loosen each two setscrews of the ND filter knob and CCD unit CC filter knob using an L shaped wrench (across flat has 0.89 mm), and remove the knobs. -
Page 39: Positioning Adjustment For Filter Knob
Tightening torque: 20 x 10 N.m (2.0 kgf.cm) 6. Rotate the ND filter knob, and check that it rotates smoothly. Filter knob Setscrews Mark (WP2 x 3) Setscrews (WP2 x 3) ND filter knob Mark CC filter knob 2-3 (E) BVP-E30/E30P M-V1... -
Page 40: Replacing The Boards Inside The Ccd Unit
Nylon rivet Nylon rivet B2.6 x 4 B2.6 x 4 B2.6 x 4 B2.6 x 4 B2.6 x 4 B2.6 x 4 Precision P2 x 5.0 Precision P2 x 5.0 K3 x 6 B2.6 x 4 2-4 (E) BVP-E30/E30P M-V1... -
Page 41: Bvp-E30/E30P M-V1
Install a new board in the reverse order of steps 1 to 3. Nylon rivet Nylon rivet B2.6 x 4 B2.6 x 4 B2.6 x 4 B2.6 x 4 B2.6 x 4 B2.6 x 4 Precision P2 x 5.0 Precision P2 x 5.0 2-5 (E) BVP-E30/E30P M-V1... -
Page 42: Adjusting Filter Position After Replacing The Dr-536 Board
2: ON ..Adjustments of all filters OFF ... Adjustment of one filter 3: ON ..Fine CCW adjustment (viewed from motor shaft) OFF ... Fine CW adjustment (viewed from motor shaft) 4: Reserved (Not used) 2-6 (E) BVP-E30/E30P M-V1... -
Page 43: Replacing The Vf Connector
+B2.6 x 6 MB-953 board SW-1075 board Handle CN1201 Screws with stopper Screw with stoper VF connector CN801 B2.6 x 5 SW-1071 board Flexible card wire 6. Reassemble the parts in the reverse order of steps 1 to 2-7 (E) BVP-E30/E30P M-V1... -
Page 44: Bvp-E30/E30P M-V1
12. Reassemble the parts in the reverse order of steps 1 to When installing the handle holder, make sure the harnesses are routed properly and are not caught between the handle holder and the chassis. Bracket (SW-1071) B2.6 x 5 2-8 (E) BVP-E30/E30P M-V1... -
Page 45: Replacing The Ret/Incom Switch
SW-1075 board INCOM switch RET switch CN1201 BTP2.6 x 6 Lock lever K4 x 10 M3 x 8 Hexagon cap screws V shoe bracket with stopper 5. Reassemble the parts in the reverse order of removal. 2-9 (E) BVP-E30/E30P M-V1... -
Page 46: Replacing The Menu Select Knob/Menu Switch/Display Switch
9. Reassemble the parts in the reverse order of removal. Switch block When installing the SW-1069 board, put the projection CN1005 of the encoder bracket into the hole of the SW-1069 CN1004 P2.6 x 5 board surely. 2-10 (E) BVP-E30/E30P M-V1... -
Page 47: Replacing The Lens Connector
P2.6 x 5 CN17 Front switch panel Precision P2.6 x 5 LENS connector CN-2210 board 6. Reassemble the parts in the reverse order of removal. TEST OUT connector 8. Reassemble the parts in the reverse order of removal. 2-11 (E) BVP-E30/E30P M-V1... -
Page 48: Replacing The Side Switch Panel Block
Precision P2.6 x 5 6. Reassemble the parts in the reverse order of removal. Side switch panel Drop protection Shield plate SW-1067 board BTP2.6 x 6 7. Reassemble the parts in the reverse order of removal. 2-12 (E) BVP-E30/E30P M-V1... -
Page 49: Replacing The Mic Connector
MB-953 board CN-2205 board CN1002 DC-DC converter (RE-201 board) P2.6 x 5 MIC connector K2.6 x 6 3. Reassemble the parts in the reverse order of removal. 5. Reassemble the parts in the reverse order of removal. 2-13 (E) BVP-E30/E30P M-V1... -
Page 50: Replacing The Mb-953 Board
CN4 (red) lifting up. CN18 CN5 (yellow) . Insert the shield plate with the notch foward as shown in the figure. CN17 CN6 (blue) Incorrect orientation may cause the unit to short out. CN15 CN16 2-14 (E) BVP-E30/E30P M-V1... -
Page 51: Replacing The Cn-2204 Board
When installing, connect the connector CN11 of the MB-953 board with the connector of the CN-2204 board located at the rear of the unit surely. 9. Reassemble the parts in the reverse order of removal. Partition (1) CN-2204 board 2-15 (E) BVP-E30/E30P M-V1... -
Page 52: Replacing The Memory Stick Case (Cn-2206 Board)
10. Install the board rail (lower) to the unit. When installing, insert two tips of the board rail (lower) into the holes of the MB-953 board surely. M3 x 8 11. Reassemble the parts in the reverse order of removal. M3 x 8 2-16 (E) BVP-E30/E30P M-V1... -
Page 53: Setup Menu
Beside above menus, the TOP menu is provided for indicating the whole configuration of the menu items. Equipment Required . BVP-E30/E30P : 1.5-inch viewfinder BVF-10/10CE (or black/white monitor) BVP-E30WS/E30WSP : 2-inch viewfinder BVF-20W/20WCE (or black/white monitor) . Connect a camera control unit CCU-550A/550AP/700A/700AP/900/900P or AC adapter AC-550/ 550CE to supply power to the camera. -
Page 54: Bvp-E30/E30P M-V1
(*1) : The display screen at the power on is changeable. For change, refer to MENU RESUME item in OTHERS Page of the MAINTE- NANCE menu. (*2) : The screen returns to the TOP menu, only when the basic operation step1 was performed and the operation started from the TOP menu. 3-2 (E) BVP-E30/E30P M-V1... -
Page 55: Top Menu
Use this menu to check the circuit boards that are suspected to have an error or to check the firmware versions. SERVICE Use this menu to adjust the circuit boards etc., or to update the firmware for service purposes. (Normally not displayed. To display, refer to Section 5-1-6.) 3-3 (E) BVP-E30/E30P M-V1... -
Page 56: Operation Menu
When TEST CHARA is set to ON CHARACTER TEST TEST TEST TEST SYNC setting Condition VF output signal CAMERA CAMERA RETURN RETURN CAMERA CAMERA RETURN RETURN TEST OUT signal CAMERA RETURN CAMERA RETURN CAMERA RETURN CAMERA RETURN Character out put TEST OUT 3-4 (E) BVP-E30/E30P M-V1... -
Page 57: Bvp-E30/E30P M-V1
50 to 109 % Sets the bottom video level of zebra 2. VF DTL ON, OFF Sets the VF detail function to ON or OFF. VF DTL GAIN 0 to 99 Sets the VF detail level. 3-5 (E) BVP-E30/E30P M-V1... -
Page 58: Bvp-E30/E30P M-V1
_99 to 99 Sets the center marker position (Vertical direction). a) When SAFETY ZONE is set to ON. Safety Zone 90 % 100 % 80 % 16:9 16:9 4:3 area 4:3 area ASPECT Safety Safety zone zone NORMAL 3-6 (E) BVP-E30/E30P M-V1... -
Page 59: Bvp-E30/E30P M-V1
Warning : Message on DIAGNOSIS information of boards, etc. d) Auto Setup : Message on auto setup. e) Status : Message on status when settings are changed using switches on the front panel or side panel. 3-7 (E) BVP-E30/E30P M-V1... -
Page 60: Bvp-E30/E30P M-V1
With IND set to ON, ! mark lights when the aspect other than the (BVP-E30WS/ aspect selected at NORMAL is selected. E30WSP only) a) Forcibly set to OFF when MSU (master setup unit) is connected b) BVP-E30/E30WS only c) BVP-E30P/E30WSP only 3-8 (E) BVP-E30/E30P M-V1... -
Page 61: Bvp-E30/E30P M-V1
When the 16:9/4:3 switch lever on the lens is set to “x0.8”, the ! (BVP-E30WS/ mark does not light even at IND ON. E30WSP only) a) “__” is displayed for BVP-E30/E30P. SWITCH ASSIGN 1 page <SWITCH ASSIGN1> GAIN 0 dB... -
Page 62: Bvp-E30/E30P M-V1
PROD ASSIGNABLE 5600K, ATW Assigns any of the following to the assignable switch. CROP, __ Factory setting : 5600K for BVP-E30/E30P “__” for BVP-E30WS/E30WSP 5600K : 5600K mode (realizing color temperature of 5600K electrically) ON/OFF switch ATW : automatic tracking white balance ON/OFF switch... -
Page 63: Bvp-E30/E30P M-V1
COLOR TEMP is not satisfactory R GAIN _99 to 99 Sets the color temperature by changing only the value of R GAIN. B GAIN _99 to 99 Sets the color temperature by changing only the value of B GAIN. 3-11 (E) BVP-E30/E30P M-V1... -
Page 64: Bvp-E30/E30P M-V1
Selects the file corresponding to the lens mounted from 16 lens files. (1 to 17) Note : When using a serial communication compatible lens, set to 17. HA14 x 8 Display only Displays the name of lens. F2.0 Display only Displays the minimum f-stop. 3-12 (E) BVP-E30/E30P M-V1... -
Page 65: Paint Menu
ON, OFF Sets the level dependence function to ON or OFF. SKIN DTL ON, OFF Sets the skin detail function to ON or OFF. MATRIX ON, OFF Sets the linear matrix correction function to ON or OFF. 3-13 (E) BVP-E30/E30P M-V1... -
Page 66: Bvp-E30/E30P M-V1
Sets the dynamic shading to ON or OFF. With set to ON, the V modulation shading is automatically adjusted in accordance with the zoom and iris positions. Note : This can be set only when the serial communication compatible lens is used. 3-14 (E) BVP-E30/E30P M-V1... -
Page 67: Bvp-E30/E30P M-V1
ENC, Y, R, G, B, Selects the output signal at the TEST OUT terminal. RETURN, VF When VF is selected, signals corresponding with the RET switch setting of the camera (camera’s video signal or return signal) will be output. 3-15 (E) BVP-E30/E30P M-V1... -
Page 68: Bvp-E30/E30P M-V1
ENC, Y, R, G, B, Selects the output signal at the TEST OUT terminal. RETURN, VF When VF is selected, signals corresponding with the RET switch setting of the camera (camera’s video signal or return signal) will be output. 3-16 (E) BVP-E30/E30P M-V1... -
Page 69: Bvp-E30/E30P M-V1
In the ABS mode, the KNEE POINT, R, G, B and KNEE SLOPE R, G, B values are highlighted so that the absolute values can be checked. To set the ABS mode to OFF : Press the MENU SELECT knob again. 3-17 (E) BVP-E30/E30P M-V1... -
Page 70: Bvp-E30/E30P M-V1
Press the MENU SELECT knob and highlight “ABS”. In the ABS mode, values excepting LIMITER M are highlighted so that the absolute values can be checked. To set the ABS mode to OFF : Press the MENU SELECT knob again. 3-18 (E) BVP-E30/E30P M-V1... -
Page 71: Bvp-E30/E30P M-V1
To set the ABS mode to OFF : Press the MENU SELECT knob again. a) This function compensates for decreases by the knee aperture in the detail level at the high luminance level part of the camera subject. 3-19 (E) BVP-E30/E30P M-V1... -
Page 72: Bvp-E30/E30P M-V1
Adjusts the hue width the skin tone detail function affects for each channel. _99 to 99 Adjusts the saturation level the skin tone detail function affects for each channel. LEVEL _99 to 99 Sets the skin tone detail amount to each channel. 3-20 (E) BVP-E30/E30P M-V1... -
Page 73: Bvp-E30/E30P M-V1
Linear matrix that divides the chroma phase width of the linear matrix into 16 segments and can adjust each individually. PRESET MATRIX : Addition of the linear matrix value fixed in the standard specification. OHB MATRIX : Linear (multi) matrix for matching the color between the cameras. 3-21 (E) BVP-E30/E30P M-V1... -
Page 74: Bvp-E30/E30P M-V1
Linear matrix that divides the chroma phase width of the linear matrix into 16 segments and can adjust each individually. PRESET MATRIX : Addition of the linear matrix value fixed in the standard specification. OHB MATRIX : Linear (multi) matrix for matching the color between the cameras. 3-22 (E) BVP-E30/E30P M-V1... -
Page 75: Bvp-E30/E30P M-V1
Sets the cross color suppression function to ON or OFF. SATURATION page <SATURATION> LEVEL : OFF Item Setting Description LEVEL _99 to 99 Sets the chroma saturation level. ON, OFF Sets the saturation function to ON or OFF. 3-23 (E) BVP-E30/E30P M-V1... -
Page 76: Bvp-E30/E30P M-V1
1/60, 1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000, ECS 25PsF 1/50, 1/60, 1/125, 1/250, 1/500, 1/1000, 1/2000 b) ECS frequency setting Format ECS Variable Range 59.94I 60.0 to 6000 Hz 50.0 to 6000 Hz 29.97PsF 30.0 to 7000 Hz 25PsF 25.0 to 7000 Hz 3-24 (E) BVP-E30/E30P M-V1... -
Page 77: Bvp-E30/E30P M-V1
MENU SELECT knob to store. CAM CODE Display only Displays the model name of the scene file saved in the memory stick. DATE Display only Displays the date when the scene file was created in the memory stick. 3-25 (E) BVP-E30/E30P M-V1... -
Page 78: Maintenance Menu
Selects the test signal. OFF : No test signal is output. Outputs the TEST SAW signal. Outputs the 3STEP or 10STEP TEST signal. a) This is set in TEST 2 MODE of <OTHERS page> on the MAINTENANCE menu. 3-26 (E) BVP-E30/E30P M-V1... -
Page 79: Bvp-E30/E30P M-V1
CROP : OFF(16:9) Item Setting Description FORMAT 59.94I, 29.97 PsF Selects interlace system/progressive system (PsF). (BVP-E30/E30WS only) 50I, 25 PsF (BVP-E30P/E30WSP only) PsF-SHUTTER ON, OFF Turns ON or OFF the function to turn on the shutter automatically LINK when the progressive system (PsF) is selected. -
Page 80: Bvp-E30/E30P M-V1
_99 (peak light detection) ↔ 99 (average value detection of whole screen) IRIS GAIN _99 to 99 Sets the iris gain. (hunting and speed change) AUTO IRIS ON, OFF Sets the auto iris function to ON and OFF. Setting screen indicates the auto iris window frame. 3-28 (E) BVP-E30/E30P M-V1... -
Page 81: Bvp-E30/E30P M-V1
Adjusts so that R and B are matched to the G ch white shading. If consistent lighting is not available, use the RB mode only. 3D WHITE SHAD ON, OFF Sets the 3D white shading function to ON or OFF. 3-29 (E) BVP-E30/E30P M-V1... -
Page 82: Bvp-E30/E30P M-V1
Setting Description CB MODE SMPTE, EIA, Selects the built-in color bar. FULL (75 %), FULL (100 %) Q-FILTER NORMAL, WIDE Selects the encoder Q filter band (BVP-E30/E30WS NORMAL : 0.5 MHz only) WIDE : 1.3 MHz 3-30 (E) BVP-E30/E30P M-V1... -
Page 83: Bvp-E30/E30P M-V1
DATE TYPE 1 to 6 Sets the date and time display. 1 : Y/Mn/D (Month is a numeral) 2 : Mn/D (Month is a numeral) 3 : D/M/Y 4 : D/M 5 : M/D/Y 6 : M/D 3-31 (E) BVP-E30/E30P M-V1... -
Page 84: Bvp-E30/E30P M-V1
Linear matrix that divides the chroma phase width of the linear matrix into 16 segments and can adjust each individually. PRESET MATRIX : Addition of the linear matrix value fixed in the standard specification. OHB MATRIX : Linear (multi) matrix for matching the color between the cameras. 3-32 (E) BVP-E30/E30P M-V1... -
Page 85: Bvp-E30/E30P M-V1
Note : When set to OFF, “TOP” display at the right top on the menu does not appear. To display the TOP menu, set the DISPLAY switch from OFF to MENU, while holding down the MENU SELECT knob. 3-33 (E) BVP-E30/E30P M-V1... -
Page 86: Bvp-E30/E30P M-V1
Registers the adjusted value of each item to the reference file. the MENU SELECT knob. ALL PRESET Execute by pressing Resets the current values in the reference file to the factory preset the MENU SELECT values. (This setting does not affect the reference file.) knob. 3-34 (E) BVP-E30/E30P M-V1... -
Page 87: File Menu
SELECT knob to store. CAM CODE Display only Displays the model name of the operator file saved in the memory stick. DATE Display only Displays the date when the operator file was created in the memory stick. 3-35 (E) BVP-E30/E30P M-V1... -
Page 88: Bvp-E30/E30P M-V1
SELECT knob to store. CAM CODE Display only Displays the model name which created the scene file saved in the memory stick. DATE Display only Displays the date when the scene file was created in the memory stick. 3-36 (E) BVP-E30/E30P M-V1... -
Page 89: Bvp-E30/E30P M-V1
SELECT knob to store. CAM CODE Display only Displays the model name which created the reference file saved in the memory stick. DATE Display only Displays the date when the reference file was created in the memory stick. 3-37 (E) BVP-E30/E30P M-V1... -
Page 90: Bvp-E30/E30P M-V1
Sets the minimun f-stop. SELECT CURRENT 1 to 100 Selects the current lens. LENS OHB FILE page <OHB FILE> STORE FILE Item Setting Description STORE FILE Execute by pressing Stores the OHB file. the MENU SELECT switch. 3-38 (E) BVP-E30/E30P M-V1... -
Page 91: Bvp-E30/E30P M-V1
Clears the ND offset in the OHB file to 0. the MENU SELECT knob. OHB MATRIX Execute by pressing Clears the matrix in the OHB file to 0. the MENU SELECT knob. M.S. FORMAT Execute by pressing Formats the memory stick. the MENU SELECT knob. 3-39 (E) BVP-E30/E30P M-V1... -
Page 92: Diagnosis Menu
TOP MENU DISABLE: OFF OFFSET : 7E SCENE FILE TYPE : OFFSET2 : 25 CAMERA NO : UNDEFINED FLR OFFSET : 7F TEST(VF) MODE : EXT VF OFFSET ADJUST: OFF TEST OUT : ENC TEST SIGNAL : OFF STORE 3-40 (E) BVP-E30/E30P M-V1... -
Page 93: Bvp-E30/E30P M-V1
V-LINE COMP page (Section 5-7) CONFIG page <V-LINE COMP> <CONFIG> COMPENSATION MODE: OFF [BOARD] CHANNEL SELECT TEST CHARACTER : OFF : 226 : 261 CURSOR: OFF H: 170 V: ev194 EXEC LEVEL : -- SAVE CANCEL DELETE 3-41 (E) BVP-E30/E30P M-V1... -
Page 95: File System
Section 4 File System The BVP-E30/E30P/E30WS/E30WSP are equipped with various file systems for managing data. In this section, the menu operations are described as follows. Example: When executing WRITE (CAM → MS) at the OPERATOR FILE page of the OPERATION menu. -
Page 96: Operator File
(Step 2) (Step 1) Camera unit Calling (Step 3) Initializing (Step 5) Preset Operator File Current Operator Preset Operator File Factory-set File Data value Storing (Step 4) Output to hardware Fig. 4-2. Operating Procedure for Operator Files 4-2 (E) BVP-E30/E30P M-V1... -
Page 97: Preset Operator File
[FILE] → [OPERATOR|FILE] → [STORE|PRESET|FILE] Initializing (Refer to step 5 of Fig. 4-2.) Using FILE Menu of This Unit Use when initializing the changed Preset Operator File data to their factory-set values. [FILE] → [FILE|CLEAR] → [PRESET|OPERATOR] 4-3 (E) BVP-E30/E30P M-V1... -
Page 98: Scene File
With MSU Press and light up the SCENE FILES button of the desired number when the STORE button is dark. Press the lit button again to turn it dark and resume the previous status. 4-4 (E) BVP-E30/E30P M-V1... -
Page 99: Bvp-E30/E30P M-V1
Camera unit Storing in Storing memory stick (Step 1) (Step 1) Scene File Memory stick Current paint data Calling Readng from memory stick (Step 2) (Step 3) Output to hardware Fig. 4-3. Operating Procedure for Scene Files 4-5 (E) BVP-E30/E30P M-V1... -
Page 100: Reference File
The temporary paint amount and scene file amount will be cleared and the reference file will be reset to the state stored in. With MSU Press STANDARD button to reset the reference file item to the state stored in. 4-6 (E) BVP-E30/E30P M-V1... -
Page 101: Bvp-E30/E30P M-V1
(Step 1) Camera unit (Step 3) Storing (Step 1) Initializing (Step 4) Reference File Reference File Current paint data factory-set value (Initial value 0) Calling (Step 2) Output to hardware Fig. 4-4. Operating Procedure for Reference Files 4-7 (E) BVP-E30/E30P M-V1... -
Page 102: Lens File
(12) Store the Lens File. [FILE] → [LENS|FILE] → [STORE|FILE] *1 : The center marker position is stored in the Lens File immediately after the position is aligned and not when executing the Lens File store. 4-8 (E) BVP-E30/E30P M-V1... -
Page 103: Bvp-E30/E30P M-V1
Using OPERATION Menu of This Unit Select the Lens File. [OPERATION] → [LENS|FILE] Initializing Using FILE Menu of This Unit All data of the lens file being currently selected will be initialized to the factory setting values. 4-9 (E) BVP-E30/E30P M-V1... -
Page 104: Ohb File
2 Select 1 by the ND filter knob, and adjust the lens iris so that the video level is 80 to 50 % (560 to 350 mV), and then adjust the white balance automatically. [MAINTENANCE] → [AUTO|SETUP] → [AUTO|WHITE] 4-10 (E) BVP-E30/E30P M-V1... -
Page 105: Bvp-E30/E30P M-V1
[OHB|File] → [Adjusting] → [Matrix] Change the adjustment display by pressing the button 1, 2 of sub menu, and adjust the value of the OHB matrix. (7) Store the OHB File. [OHB|File] → [OHB|store] → [Store] 4-11 (E) BVP-E30/E30P M-V1... -
Page 106: File Items
Test 1 On (TEST SAW) — — — — — Test 2 On — — — — — Test2 Mode — — — — — — 3Step Optical Filter Filter Position — — — — — 1/1B (WS only) (Continued) 4-12 (E) BVP-E30/E30P M-V1... -
Page 107: Bvp-E30/E30P M-V1
B Flare — — Black Master Black — — — R Black — — — — G Black — — — — B Black — — — — * : White Gamma RGB mode only (Continued) 4-13 (E) BVP-E30/E30P M-V1... -
Page 108: Bvp-E30/E30P M-V1
— Skin 3 Gate On — — — — — — Skin 3 Level — — — Skin 3 Phase — — — Skin 3 Width — — — Skin 3 Sat — — — (Continued) 4-14 (E) BVP-E30/E30P M-V1... -
Page 109: Bvp-E30/E30P M-V1
— — — RGB Black Gamma — — — — High Range Low Key Saturat Low Key Saturation On — — — — Range — — — — High Low Key Saturation — — — (Continued) 4-15 (E) BVP-E30/E30P M-V1... -
Page 110: Bvp-E30/E30P M-V1
— BARS Mode — — — — — — UC : SMPTE CE : FULL (75 %) Cross Color — — — — Suppress Level — — — * : White Gamma RGB mode only (Continued) 4-16 (E) BVP-E30/E30P M-V1... -
Page 111: Bvp-E30/E30P M-V1
Zebra 1 Width — — — — 10 % Zebra 2 Level — — — — 100 % VF DTL VF DTL On — — — — — VF DTL Gain — — — — (Continued) 4-17 (E) BVP-E30/E30P M-V1... -
Page 112: Bvp-E30/E30P M-V1
16:9 (WS only) Format — — — — UC : 59.94I CE : 50I Shutter Link Mode — — — — — — Level Auto Set Up White Setup Mode — — — — — — LEVEL (Continued) 4-18 (E) BVP-E30/E30P M-V1... -
Page 113: Bvp-E30/E30P M-V1
— — — — — +6dB +12dB Gain [H] — — — — — White [B] — — — — — Outout [DCC] — — — — — Auto Knee RE.Rotation — — — — — 4-19 (E) BVP-E30/E30P M-V1... -
Page 115: Electrical Alignment
. Grayscale chart (16:9, transparent) (Sony part No. : J-6394-080-A) . Grayscale chart (4:3, reflective) (Commercially available, Refer to Section 5-1-5) . Flexible card wire (30P, 140 mm) (2 pieces) (Sony part No. : 1-823-429-11) . EX Harness (3 pieces) (Sony part No. : 1-961-653-21) Equipment . -
Page 116: Notes On Adjustment
*1: Represented as “CCU” simply for convenience in wirting in this section. *2: Represented as “CA” simply for convenience in wirting in this section. *3: Used when CA-950/950P and CCU-900/900P are used. *4: Used when CA-570/570P and CCU-550A/550AP/700A/ 700AP are used. 5-2 (E) BVP-E30/E30P M-V1... -
Page 117: Initial Settings
FILTER button (CC) → ON . Menu operation block (touch panel) PAINT button → (2/3) [White|Clip] → [White|Clip|Off] → ON PAINT button → (2/3) [White|Clip] → [White|Clip|Off] * : Press FUNCTION button and select from function menu screen 5-3 (E) BVP-E30/E30P M-V1... -
Page 118: Presetting Compensation Data
In this section, the menu operations are described as follows: Example : When selecting ENC of TEST OUT at the VA TRIMMING page of the SERVICE menu. MENU : SERVICE PAGE : VA TRIMMING TEST OUT → ENC ITEM : 5-4 (E) BVP-E30/E30P M-V1... -
Page 119: Maintaining The Grayscale Chart
Adjust the position and angle of the light source so that the whole surface of the chart is evenly 2000 lx. Light the chart from almost the same direction and height as the camera to shoot the chart. 5-5 (E) BVP-E30/E30P M-V1... -
Page 120: Bvp-E30/E30P M-V1
4. Adjust the luminance control of the pattern box so that the white portion in the center of the chart is 573 ± 6 cd/m This corresponds to the luminous intensity on the 89.9 %-reflective chart at 2000 lx. Chart Luminance meter 5-6 (E) BVP-E30/E30P M-V1... -
Page 121: Board Adjustment
Specifications : A = 0 ± 10 mV 2. Flare Offset G Adjustment Test Point : TP1 (GND : E1) Adjustment Point . ITEM : FLR OFFSET [G] Specifications : A = 0 ± 10 mV VA-226 board (A side) 5-7 (E) BVP-E30/E30P M-V1... -
Page 122: Offset Adjustment
Specifications : The spot of the vectorscope shall not change. 4. Menu setting OFFSET ADJUST → B ITEM : 5. OFFSET B Adjustment Adjustment Point . ITEM : OFFSET [B] Specifications : The spot of the vectorscope shall not change. 5-8 (E) BVP-E30/E30P M-V1... -
Page 123: Pa-272/273/274 Boards Adjustment
. Lens Iris → F11 . Menu setting MENU : OPERATION RV1/PA-272 board PAGE : PRESET WHITE COLOR TEMP → 3200k ITEM : . WHITE BAL switch (on the side panel) → RV1/PA-273 board PRESET (3200 K) RV1/PA-274 board 5-9 (E) BVP-E30/E30P M-V1... -
Page 124: Board Adjustment
Reference value: 3 mV (0.5 IRE) or less TEST1 TEST2 (10STEP) (Waveform monitor) 4. Store the TRIMMING data. (Press the MENU SELECT knob to execute.) ITEM: STORE 5. Setting after adjustments Set TEST1 and TEST2 to OFF. 5-10 (E) BVP-E30/E30P M-V1... -
Page 125: Video Level Adjustment (1)
. ITEM : Y LEVEL Specifications : NTSC : A = 714 ± 2 mV A = 700 ± 2 mV PAL : (NTSC) (Oscilloscope) (PAL) E501 TP501 TP502 TP503 (Oscilloscope) TP800 DPR-261 board (A side) 5-11 (E) BVP-E30/E30P M-V1... -
Page 126: Test Out Level Adjustment
PAL : (NTSC) (Waveform monitor) (PAL) E501 TP501 TP502 TP503 (Waveform monitor) After the adjustment is completed, store the TRIM- MING data. (Press the MENU SELECT knob to execute.) ITEM : STORE TP800 DPR-261 board (A side) 5-12 (E) BVP-E30/E30P M-V1... -
Page 127: Sc Frequency Adjustment
. ITEM : VBS C LEVEL E501 Specifications : CROMA LEVEL Each beam spot of vectorscope stays TP501 TP502 TP503 (NTSC) (PAL) Burst spot 75 % TP800 11 10 (Vectorscope) DPR-261 board (A side) 5-13 (E) BVP-E30/E30P M-V1 inside the frame “4”. -
Page 128: Rpn Pixel Concealment
CONCEAL MODE → ON ITEM : . When the RPN recognition is difficult since the RPN hides behind the character on a screen or is very close to the character : ITEM : TEST CHARACTER → OFF 5-14 (E) BVP-E30/E30P M-V1... -
Page 129: Rpn Compensation Adjustment
Auto Compensation Setting after Adjustment 1. Move the cursor → to “AUTO COMPENSATION”, ITEM : COMPENSATION MODE → OFF and press the MENU SELECT knob. “APR EXCUTING” will be displayed, and the com- pensation will be performed. 5-15 (E) BVP-E30/E30P M-V1... -
Page 130: White Vertical Line Compensation
7. If perform this adjustment again or any other vertical very close to the character : line noises remain, repeat steps 2 to 5. ITEM : TEST CHARACTER → OFF Setting after Adjustment ITEM : COMPENSATION MODE → OFF 5-16 (E) BVP-E30/E30P M-V1... -
Page 131: V-Sub Voltage Adjustment
(Oscilloscope) 2. Perform V-SUB [G] adjustment in the same manner as step 1. Test Point : IC1- pin14/PA-273 board (GND : E501/DPR-261) TP800 Adjustment Point . ITEM : V-SUB [G] 11 10 DPR-261 board (A side) 5-17 (E) BVP-E30/E30P M-V1... -
Page 132: V-Reg Voltage Adjustment
3. Perform V-REG [B] adjustment in the same manner as step 1. Test Point : H rate CN1- pin14/PA-272 board (GND : E501/DPR-261) CN2- pin1/TG-229 board (GND : E501/DPR-261) V1 + V2 Specifications : V-REG [B] = (Calculate with hexadecimal) (Oscilloscope) 5-18 (E) BVP-E30/E30P M-V1... - Page 133 (Press the MENU SELECT knob to execute.) ITEM : STORE Setting after Adjustment Restore the CCD block to the original position. 14pin PA-272/273/274 board (A side) E501 TP501 TP502 TP503 TP800 11 10 DPR-261 board (A side) 5-19 (E) BVP-E30/E30P M-V1...
- Page 136 BVP-E30 (UCJ) BVP-E30P (CE) BVP-E30WS (UCJ) Printed in Japan Sony Corporation BVP-E30WSP (CE) J, E 2004. 7 08 B&P Company 9-968-049-01 ©2004...