Table of Contents
Advertisement
Quick Links
Installation Instructions
IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE
Information is subject to change.
Please refer to our website to obtain the most current product specification,
technical & warranty information.
ESW 408x-14
ESW 47xx
ESW 48xx
To prevent accidents
and machine damage
read these instructions
before
installation or use.
Advertisement
Table of Contents
Related Manuals for Miele ESW 408x-14
Summary of Contents for Miele ESW 408x-14
-
Page 1: Installation Instructions
IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. ESW 408x-14 ESW 47xx ESW 48xx To prevent accidents and machine damage... -
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Before installation make sure that ESW 408x-14 the voltage and frequency listed on the Only install the warming drawer in data plate correspond with the combination with built-in appliances household electrical supply. This data recommended by the manufacturer. -
Page 3: Combination Possibilities
ESW 408x-14 Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Combination possibilities Installation with an oven ( 3 0 m ( 2 2 * / 2 3 * * m m... - Page 4 ESW 408x-14 Installation with a speed oven ( 2 2 * / 2 3 * * m m ( 5 4 0 ( 5 ( 5 6 ( 5 6 - 5 6 * Machine with glass front ** Machine with stainless steel front...
- Page 5 ESW 408x-14 Installation with a steam oven ( 2 2 * / 2 3 * * m ( 4 4 0 ( 5 ( 5 4 ( 5 6 - 5 6 * Machine with glass front ** Machine with stainless steel front...
- Page 6 ESW 408x-14 Installation with a coffee machine ( 2 0 ( 4 6 0 ( 5 ( 5 5 ( 5 6 * / 2 * * ) * Machine with glass front ** Machine with stainless steel front...
- Page 7 ESW 408x-14 BRWS Combination possibilities Installation with an oven ( 3 0 m ( 2 2 * / 2 3 * * m m ( 5 4 8 ( 5 4 0 ( 5 ( 5 6 a Cut-out for venting the oven...
- Page 8 ESW 408x-14 BRWS Installation with a speed oven ( 2 2 * / 2 3 * * m m ( 5 4 0 ( 5 ( 5 6 ( 5 6 - 5 6 * Machine with glass front ** Machine with stainless steel front...
- Page 9 ESW 408x-14 BRWS Installation with a steam oven ( 2 2 * / 2 3 * * m ( 4 4 0 ( 5 ( 5 4 ( 5 6 - 5 6 * Machine with glass front ** Machine with stainless steel front...
- Page 10 ESW 408x-14 BRWS Installation with a coffee machine ( 2 0 ( 4 6 0 ( 5 ( 5 5 ( 5 6 * / 2 * * ) * Machine with glass front ** Machine with stainless steel front...
- Page 11 ESW 47xx Solo installation Side view a A base is required for solo installations...
- Page 12 ESW 47xx Installation with an oven Side view with oven...
- Page 13 ESW 48xx Solo installation Side view a A base is required for solo installations...
- Page 14 ESW 48xx Installation with an oven Side view with oven...
-
Page 15: Installation
Installation Miele appliances can be installed flush or proud. Discuss your installation requirements with your architect, designer and installer. Check that the base of the warming drawer is clean and level. Only then will it function properly. When inserting the appliance, wear work gloves to avoid injuries. -
Page 16: Aligning The Appliance Front
^ Remove the screws a from the left and right sides of the drawer front. ^ Carefully lift the control panel out of the drawer. Be careful not to pull or damage the power cord. ESW 408x-14 ESW 47xx / ESW 48xx... - Page 17 ^ Tighten the screws on the inside of the drawer front. ^ Replace the control panel, use caution with the power cord. ^ Replace the screws on the left and right sides of the drawer front. ESW 408x-14 ESW 47xx / ESW 48xx...
-
Page 18: Integrated Installations
Installation Integrated installations Custom made front panels can be installed with models ESW 4702 FB and ESW 4802 FB. The custom panel must be at least " (19 mm) thick and made of heat resistant material 140 °F (60 °C). The front panel, including handle, must not exceed 11 lb (5 kg) in weight. - Page 19 Installation ^ Remove the cable tie from the panel. ^ Screw the removed panel to the custom panel (see illustration). ^ Hook the panel into the bottom. Make sure the seal is seated correctly. ^ Replace and slightly tighten the screws on the inside of the drawer front.
-
Page 20: Electrical Connection
Electrical connection Power supply CAUTION: Before servicing, This appliance is equipped with a 5 ft disconnect the power supply by (1.5 m) long power cord with a either removing the fuse, shutting off three-prong grounding plug ready for the power main or manually connection to a 120 V, 15 A, 60 Hz "tripping"... -
Page 21: Help Protect Our Environment
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing Old appliances contain materials that materials are biodegradable and can be recycled. Please contact your recyclable. Please recycle. local recycling authority about the possibility of recycling these materials. - Page 22 Alteration rights reserved / 2811 M.-Nr. 07 342 380 / 07 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.