1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC Power Jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1 Precautions 1-4 Installation Precautions 1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage required for carrying the product. cables and install it firmly. Contact with the high- voltage cable or the antenna falling over may 2.
2 Product Specifications 2 Product specifications 2-1 Fashion Feature Supreme Digital Interface & Networking -With a built-in HD digital tuner, it supports HD broadcasting with no particular set-top box and provides simple access with a single remote control. Excellent Picture Quality -DNIe technology provides life-like clear images.
3 Alignments and Adjustments 3 Alignments and Adjustments 3-1 Service Instruction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3.
3 Alignments and Adjustments 3-2 How to Access Service Mode 3-2-1 Entering Factory Mode 1. To enter "Service Mode" Press the remote -control keys in this sequence : - If you do not have Factory remote - control - If you have Factory remote - control - The buttons are active in the service mode.
Carrier Mute TTX Group Auto Gamma Language English Auto Power Panel Option AMLCD_INT Auto FM ---- 2HDMI High Deviation ---- Brt.Sensor ---- EnergySave TTX List Debug LBE/FBE Ch.Table SUWON FRC(Micronas) Dynamic CE iDTV_Cntry FRC(Samsung) Dynamic Dimming Dynamic Contrast Tuner TOP...
3 Alignments and Adjustments 3-4 Service Adjustment 3-4-1 White Balance - Calibration If picture color is wrong, do calibration first. Equipment : CA210, Patten : chess pattern Execute calibration in Factory Mode Source AV : PAL composite, Component : 1280*720/60Hz PC : 1024*768/60Hz ( chess patten ) 3-4-2 White Balance - Adjustment...
Page 18
3 Alignments and Adjustments 3-4-3 Conditions for Measurement 1. On the basis of toshiba ABL pattern : High Light level (57 IRE) - INPUT SIGNAL GENERATOR : MSPG-925LTH * Mode 2 : 744X484@60 Hz 6 : 1280X720@60 Hz NO 21 : 1024X768@60 Hz * Pattern NO 36 : 16 Color Pattern NO 16 : Toshiba ABL Pattern 2.
Page 19
3 Alignments and Adjustments d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode) - Adjust red gain ('x') and blue gain ('y') to the color coordinates. * Do not adjust the green gain and sub-contrast (Y) data. Picture 4-3 Toshiba ABL Pattern High light Measurement point...
3 Alignments and Adjustments 3-5 Software Upgrade 3-5-1 How to Update Flash ROM 1. Installthe Flash Downloader ConnectSet(Service Jack)and Jig Cable to execute Program Update. 2. Flash Downloader program update -Before Turning on the set,Click "connect"which is under of OSD Screen! -Turn on the Set.
4 Troubleshooting 4 Troubleshooting 4-1 First Checklist for Troubleshooting 1. Check the various cable connections first. - Check to see if there is a burnt or damaged cable. - Check to see if there is a disconnected cable connection or a connection is too loose. - Check to see if the cables are connected according to the connection diagram.
4 Troubleshooting 4-2 Checkpoints by Error Mode 4-2-1 No Power LAMP off, power indicator Check a connection a power cable. LED red color? Does proper DC 12V Change a Assy PCB Power. appear at CN800? Does proper DC A3.3V, Check a IC809, IC802. A5V appear at Change a main PCB ass'y.
Page 23
#30, 22, 38(R, G, B) of IC500? cable. Change a main PCB ass'y. Does the digital data appear Check a IC500 at the output of Change a main PCB ass'y. LVDS (R563_OP~R572_OP)? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 24
4 Troubleshooting WAVEFORMS R,G,B Output Signal of IC500...
Page 25
Check a a IC 500 R503~R510? Change a main PCB ass'y. Does the digital data Check a IC500 appear at output of IC500 Change a main PCB ass'y. LVDS(R563_OP~R572_OP)? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace lcd panel?
Page 26
4 Troubleshooting Digital Output Data of IC500 Signal of HDMI(Data)
Page 27
Does the signal appear at Change a main PCB ass'y. #8 of IC500? Does the digital data appear Check a IC500. at output of Change a main PCB ass'y. R563_OP~R572_OP? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel?
Page 29
Dose the signal appear at Check a connection harness. #10 of IC500? Does the signal appear at Check a IC515. Out of IC500 Change a main PCB ass'y R563_OP~R572_OP? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace lcd panel?
Page 30
4 Troubleshooting WAVEFORMS CVBS Output Signal 4-10...
Page 31
Check a connection harness. #21, #31 of IC500? Does the digital data appear Check a IC500. at Output of IC500, Change a main PCB ass'y. R563_OP~R572_OP? Check a LVDS cable? Please, Call to Samsung Co. LTD. Replacea lcd panel? 4-11...
Page 32
4 Troubleshooting WAVEFORMS Digital Output Data of IC500 Analog Signal(Y,C) to IC500 4-12...
4 Troubleshooting 4-2-7 No Sound Connect a sound cable. Picture is display, no sound. control a volume. Does the signal appear at Pin #10, #16(CH1_L, R Sound) Check a connection harness and and Pin #3, #9 headphone jack / Side AV. (CH2_L, R Sound) of IC603? Check the DC 12V...
Page 34
4 Troubleshooting WAVEFORMS The Signal are Inputed to IC603 DC +12V 4-14...
Page 35
5 Exploded View & Parts List 5 Exploded View and Parts List - You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 5-1 LE27S71B Exploded View M0013 T0447 T0159 M0215 T0003 T0175 M0014 T0175 M0013...
6 Electrical Parts List 6 Electrical Parts List You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 6-1 LE27S71B Parts List Level Loc. No. Code No. Description & Specification Q'ty SA/SNA LE27S71BX/XEC LE27S71B,Q52A/27S70-GSM,27,LCD-TV,SPAIN M0001 BN90-00978A ASSY COVER FRONT;27T70,EO,ABS+PMMA,HB,BK...
Page 44
6 Electrical Parts List Level Loc. No. Code No. Description & Specification Q'ty SA/SNA M2893 BH39-00362B LEAD CONNECTOR;RE32**,UL1007#26,5P,150mm T0076 BN39-00615D CBF HARNESS;BORDEAUX,1617#22,3P,1P,RING, M2893 BN39-00659A LEAD CONNECTOR;RE32*CMO,UL1007#26,14/12P M2893 BN39-00691B LEAD CONNECTOR;LE32R71BX,UL1007#26,16P,1 M2893 BN39-00721A LEAD CONNECTOR-LVDS;Sonoma,UL1571#30,30P BN61-02207A BRACKET-PANEL SIDE;Bordeaux 26,SECC,T1.2 BN61-02364A BRACKET-STAND LINK;SONOMA 32,SECC,T1.6 M0114 BN61-02500A HOLDER-WIRE;NYLON6.6,NATURAL...
7 Block Diagrams 7 Block Diagram - This Document can not be used without Samsung’s authorization FLASH MEMORY AT49BV802 M30840 MICOM OPTION LM4810 74HC STA323W SOUND OUT MAX232...
Page 110
8 Wiring Diagrams CN221 - Front control NAME SDA-T SCL-T GND GND IDENT HP-L HP-R INPUT1 INPUT1 INPUT2 Function Define - A5V Front control board poewr supply - KEY INPUT1,2/SDA/SCL Key control, from the memu, change up/down Etc. - IR Remote control signal - LED Control the timing and stand by LED color...
Page 112
8 Wiring Diagrams 8-4 Power Board Layout...
Page 113
8 Wiring Diagrams CN801 - AC Input NAME Live Netural VOLTAGE Functing Define - Refer to : AC Input CN801 - Main Board power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Functing Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CNM804 - Panel control...
Page 114
8 Wiring Diagrams CN802 - Inverter power supply NAME 24V GND GND GND GND Functing Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN803 - Inverter power supply NAME 24V GND GND GND GND...
Page 116
8 Wiring Diagrams CN801 - AC Input NAME Live Netural VOLTAGE Functing Define - Refer to : AC Input CN801 - Main Board power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Functing Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CNM804 - Panel control...
Page 117
8 Wiring Diagrams CN803 - Inverter power supply NAME 24V GND GND GND GND Functing Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN804 - Inverter power supply NAME 24V GND GND GND GND...
11 Disassembly and Reassembly 11 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the TFT-LCD WARNING : This monitor contains electrostatically sensitive devices. Use caution when handling these components. 11-1 Disassembly Cautions : 1. Disconnect the monitor from the power source before disassembly. 2.
Page 129
11 Disassembly and Reassembly Description Picture Description 2. Lift up the rear cover and remove the stand. 3. Remove Screws from the stand BRKT and lift up the stand BRKT. 11-2...
Page 130
11 Disassembly and Reassembly Description Picture Description 4. Disonnect cable from the boards. 5. Remove screws from the boards and lift up the boards. 11-3...
Page 131
11 Disassembly and Reassembly Description Description Picture 6. Remove screws and Lift up the Lcd panel. 7. Remove 5 secews from the BRKT. Lift up the BRKT. 11-4...
Page 132
11 Disassembly and Reassembly Description Description Picture 11-2 Reassembly Reassembly procedures are in the reverse order of disassembly procedures. 11-5...
13 Circuit Descriptions 13 Circuit Descriptions 13-1 Block description Bordeaux consists of three main blocks 1. Main board : Video signal processing 2. IP board : Power supply & Inverter 3. T-con board : LCD Panel control 13-1...
Page 139
13 Circuit Descriptions I I NVERTER SMPS Bordeaux consists of three main blocks 1. Main board : Video signal processing 2. SMPS : Power supply 3. T-con board : LCD Panel control 13-2...
14 Reference Infomation 14 Reference Infomation 14-1 Technical Terms - TFT-LCD - Auto Configuration(Auto adjustment) (Thin film Transistor Liquid Crystal Display) This is an algorithm to adjust monitor to optimum ADC(Analog to Digital Converter) condition by pushing one key. This is a circuit that converts from analog signal to digital signals.
Page 147
14 Reference Infomation - T.M.D.S - Interlace and Non-Interlace Methods (Transition minimized Differential Signaling) Showing the horizontal lines of the screen from the a kind of transmission method for Digital. top to the bottom in order is called the Non- It can be used from Video card to Main PBA.
Page 148
Enables high picture quality and clear sound channel to obtain the best viewing conditions. The throughout the country regardless of the location of Samsung LCD TV has both automatic and manual the viewer. channel fine-tuning features to enable the viewer to adjust their desired settings.
Page 150
14 Reference Infomation 14-2-2 Component 14-2-3 S-Video Separate RCA Green Pb (Cb) RCA Blue Pr (Cr) RCA Red Audio L 14-2-5 D-SUB RCA White Separate Audio R RCA Red Green Blue 14-2-4 A/V GND Red GND Green GND Blue RCA Yellow CVBS DDC Input power(+5V) Audio L...
Page 151
14 Reference Infomation 14-2-7 Scart 1 Signal Signal Audio output R Audio input R Video GND (RGB red) Audio output L Audio common GND RGB red input Video GND (RGB blue) Fast Blanking signal (RGB switching) Audio input L Video output GND RGB blue input Video input GND Switching voltage...
14 Reference Infomation 14-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer- generated video signals. 14-3-1 LCD Panel Mode1 mode 14-7...