Table of Contents
Related Manuals for Miele G 2XXX Series
Summary of Contents for Miele G 2XXX Series
-
Page 1: Operating Instructions
Operating instructions for dishwashers To avoid the risk of accidents or en - GB damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time. M.-Nr. -
Page 2: Table Of Contents
Contents Guide to the appliance ..........5 Appliance overview . - Page 3 Contents Operation ............32 Detergent .
- Page 4 Plumbing............59 The Miele waterproof anti-leak system ....... . . 59 Connection to the water supply .
-
Page 5: Guide To The Appliance
Guide to the appliance Appliance overview a Upper spray arm (not visible) g Filter combination b Cutlery tray (depending on model) h Data plate c Upper basket i Child safety lock in door grip (not visible) d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual compartment detergent... -
Page 6: Control Panel
Guide to the appliance Control panel a Programmes f Start/Stop button with indicator light b Delay start display g Delay start button cProgramme sequence indicator h Turbo button with indicator light d On/Off button K i Programme selector button e Check/Refill indicators This instruction book applies to several different dishwasher models. -
Page 7: Warning And Safety Instructions
Warning and Safety instructions Safety with children This appliance conforms to current This appliance is not a toy! To avoid safety requirements. Inappropriate the risk of injury, keep children well use can, however, lead to personal away and do not allow them to play in injury and damage to property. - Page 8 Warning and Safety instructions Technical safety Do not connect the dishwasher to the mains supply until it has been fully Before setting up the appliance, installed. check it for any externally visible damage. Under no circumstances Before connecting the appliance, should you use a damaged appliance.
- Page 9 If the connection cable is damaged where it can be seen that this is it must be replaced with a Miele cable necessary. by a Miele approved service technician – The stopcock has been turned off only.
-
Page 10: Correct Use
Warning and Safety instructions Installation Correct use The dishwasher must be installed Do not use solvents in the and connected in compliance with the dishwasher. Danger of explosion. installation instructions. Do not inhale or ingest dishwasher The dishwasher must be correctly detergent. - Page 11 Warning and Safety instructions Accessories Inadvertently filling the salt reservoir with powder or liquid dishwasher Only use genuine Miele spare parts detergent will damage the water and accessories with this appliance. If softener. Make sure you have picked spare parts or accessories from other...
-
Page 12: Caring For The Environment
Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for disposal human health and to the environment. -
Page 13: Energy Saving Washing
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your household water system is suitable, this dishwasher can be connected to a hot water supply for further economies. -
Page 14: Before Using For The First Time
Before using for the first time To open the door Safety lock ^ Press the release catch inside the Use the safety lock to prevent children door grip upwards and pull the door opening the dishwasher door. open. ^ To lock the door, push the slide If the door is opened during operation underneath the door grip to the right. -
Page 15: Water Softener
Before using for the first time Water softener The dishwasher is set at the factory for a hardness level of In order to achieve good cleaning 2.2 - 2.7 mmol/l (12 - 15 °d). results, the dishwasher needs to operate with soft water. Hard water If this setting corresponds to the results in the build-up of calcium hardness of your water you do not need... -
Page 16: To Programme The Water Hardness Level
Before using for the first time To programme the water hardness The number of times the Wash/Rinse programme sequence indicator flashes level tells you the value which has been set Each time a button is pressed, one of (see chart). the indicator lights will flash and light up in the control panel. -
Page 17: Checking The Programmed Water Hardness Level
Before using for the first time Checking the programmed water hardness level ^ Switch the dishwasher off using the K button. ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the K button. Keep the Start/Stop button pressed in until the Start/Stop indicator comes ^ Press the Delay start button twice. -
Page 18: Before Using The Appliance For The First Time You Require
– Rinse aid* formulated for domestic area. dishwashers. * Miele branded products are Important! Before filling the salt available from the Miele Spare Parts reservoir with dishwasher salt for the Department or via the internet at first time, you must fill it with www.miele-shop.com. -
Page 19: Salt Indicator
Before using for the first time ^ Remove the lower basket and Salt indicator unscrew the salt reservoir cap. ^ Fill the salt reservoir with dishwasher salt when the salt indicator light Water or saline solution will run out comes on. (If it comes on during a of the reservoir when the cap is programme, wait until the end of the removed. -
Page 20: Rinse Aid
Before using for the first time Rinse aid If you only ever use combination Rinse aid is necessary to ensure water products containing rinse aid in your does not cling and leave marks on dishwasher, you do not need to add crockery during the drying phase and rinse aid. -
Page 21: Rinse Aid Indicator
Before using for the first time Rinse aid indicator When the light comes on the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid in plenty of time. ^ Add rinse aid only until it is visible in the opening. -
Page 22: Setting The Rinse Aid Dosage
Before using for the first time ^ Press the Delay start button three Setting the rinse aid dosage times. You can adjust the rinse aid dosage for best results. The lowest programme indicator will flash briefly three times at intervals. The rinse aid dosage can be set from approx. -
Page 23: Loading The Dishwasher
Loading the dishwasher Note – Wide based items should be placed at an angle so that water can run off Remove coarse food residues from them freely. crockery. – The spray arms must not be blocked There is no need to rinse items under by items which are too tall or hang running water. -
Page 24: Items Not Suitable For Dishwashers
Loading the dishwasher Items not suitable for We recommend: dishwashers: – When purchasing new crockery and cutlery, make sure they are – Wooden cutlery and crockery or dishwasher-proof. items with wooden parts: these may discolour and fade. The glue used in –... -
Page 25: Upper Basket
Loading the dishwasher Upper basket Hinged cup rack ^ To make room for tall items, raise the For safety reasons, do not rack upwards. operate the dishwasher without the upper and lower baskets in place. Positioning rail (depending on model) Glasses can be arranged along the positioning rail to give them some support during the programme. -
Page 26: Universal Support (Depending On Model)
Loading the dishwasher Universal support (depending on model) This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the support and lean tall glasses against it. -
Page 27: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, the following plate dimensions In order to gain more space for taller can be accommodated. pieces of crockery in the bottom or upper basket, the upper basket can be Dishwasher with cutlery tray adjusted on three levels with 2 cm (see data plate for model number) -
Page 28: Lower Basket
Loading the dishwasher Lower basket Hinged spikes ^ For larger and heavier items such as The spikes are used for washing plates plates, serving platters, saucepans, and saucers. bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket. -
Page 29: Removable Spiked Insert
Loading the dishwasher Removable spiked insert Bottle holder (depending on model) You can remove the spiked insert to The bottle holder can be used to wash make more room for larger items of narrow items, e.g. milk and baby crockery, e.g. a large, flat pot, or bottles. -
Page 30: Cutlery
Loading the dishwasher Cutlery Cutlery tray (depending on model) If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. -
Page 31: Cutlery Basket (Depending On Model)
Loading the dishwasher Cutlery basket (depending on model) ^ Fit it into the cutlery basket if required. ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. -
Page 32: Operation
Combi tabs are available as "3 in 1" or, Miele branded dishwasher cleaning when they also contain other components products are available from the Miele such as glass and stainless steel Spare Parts Department or via the protective additives and enhanced Internet at www.miele-shop.com. -
Page 33: Adding Detergent
Operation The flap is always open at the end of a Avoid inhalation of powder programme. detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. -
Page 34: Switching On
Operation Switching on Starting a programme ^ Make sure the spray arms are not ^ Select the programme required with obstructed. the programme selector button. ^ Close the door. The indicator light next to the selected programme will come on. ^ Open the stopcock, if it is closed. -
Page 35: At The End Of A Programme
Operation At the end of a programme Unloading the dishwasher The End indicator light will come on at Dishes tend to break and chip more the end of the programme. easily when they are hot. Allow the dishes to cool until they are The dishwasher can now be opened comfortable enough to handle before and unloaded (see "Unloading the... -
Page 36: Interrupting A Programme
Operation Interrupting a programme Changing a programme A programme is interrupted as soon as Important: the door is opened. If the detergent dispenser flap has If the door is closed again, the already opened, do not change the programme will continue from the point programme. -
Page 37: Additional Functions
Additional functions Turbo Factory default setting The "Turbo" function is used to reduce If you have altered any settings from the duration of programmes in which the factory default, you can re-set them this function is available. back to the factory default settings as follows: In order to achieve optimum cleaning ^ Switch the dishwasher off using the... -
Page 38: Delay Start
Additional functions ^ Switch the dishwasher on using the Delay start On/Off button K. The start time of a programme can be delayed, e.g. to benefit from economy The Start/Stop indicator light will flash. rates of electricity. A delay start time of ^ Select the programme required with between half an hour and 24 hours can the programme selector button. - Page 39 Additional functions The time starts counting down until the Starting a programme before the programme start time: in one hour Delay start period has elapsed: increments for delay start periods of A programme can be started before the over 10 hours, and in half hour Delay start period has elapsed.
-
Page 40: Cleaning And Care
The outer surfaces of the surface to alter or discolour. dishwasher are susceptible to scratching. ^ Clean the front using a damp Miele Contact with unsuitable cleaning microfibre E-cloth* or with a sponge agents can alter or discolour the and a solution of hot water and outer surfaces. -
Page 41: Cleaning The Filters In The Wash Cabinet
Cleaning and care Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. The dishwasher must not be used without all the filters in place. - Page 42 Cleaning and care ^ Replace the filter combination so that To clean the inside of the filter, the flap must be opened: it lies flat in the base of the wash cabinet. ^ Press catches a together in the ^ Then turn the handle clockwise to direction of the arrows as shown, and open the filter b.
-
Page 43: Cleaning The Spray Arms
Cleaning and care ^ Remove the lower basket. Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. -
Page 44: Problem Solving Guide
Problem solving guide With the aid of the following guide, faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations. - Page 45 Problem solving guide Problem Possible cause Remedy The Wash/Rinse, There may be a technical – Clean the water inlet filter Drying and End fault. and clean the drain pump indicator lights flash and non-return valve as simultaneously. described in "Maintenance". If this does not resolve the problem, –...
-
Page 46: The Dishwasher Does Not Fill/Drain
Problem solving guide The dishwasher does not fill/drain. Problem Possible cause Remedy The Inlet/Drain check The stopcock is Open the stopcock fully. indicator flashes. closed. The dishwasher stops Before rectifying the problem during a programme. you must: The Inlet/Drain – Switch the dishwasher off indicator flashes. -
Page 47: General Problems
Problem solving guide General problems Problem Possible cause Remedy Detergent residue is left The dispenser was still Make sure the dispenser is in the dispenser at the damp when detergent dry before adding end of a programme. was added. detergent. The detergent Clogged detergent Clean the detergent from... -
Page 48: Noises
Problem solving guide Noises Problem Possible cause Remedy Knocking noise in the A spray arm is knocking Interrupt the programme, wash cabinet. against an item in a and rearrange the items basket. which are obstructing the spray arm. Items of crockery are Interrupt the programme, Rattling noise in the wash cabinet. -
Page 49: Unsatisfactory Washing Result
Problem solving guide Unsatisfactory washing result Problem Possible cause Remedy The dishes are not The dishes were not loaded See notes in "Loading the clean. correctly. dishwasher" The programme was not Select a more intensive powerful enough. programme. See Programme chart. - Page 50 Problem solving guide Problem Possible cause Remedy Dishes, cutlery The amount of rinse aid Replenish the reservoir, and glasses are may be insufficient, or the increase the dosage or not dry or are rinse aid reservoir empty. change the brand of rinse aid. flecked.
- Page 51 Problem solving guide Problem Possible cause Remedy Glassware has a This may be caused by the Change your detergent. brown or blue tinge, detergent. and film cannot be wiped off. Glassware is dull and The glasses are not There is no remedy. discoloured;...
-
Page 52: Maintenance
^ Replace the filter and seal, making union. This filter is available from the Miele Spares Parts dept. sure they are sitting correctly. ^ Reconnect the inlet hose to the Cleaning the filter:... -
Page 53: Cleaning The Drain Pump And Non-Return Valve
Maintenance Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. -
Page 54: Programme Chart
Programme chart Programme When to use Sensor wash 55-65°C Sensor controlled programme for normally soiled crockery Quick wash 40°C "Quick programme" for lightly soiled crockery, e.g. party crockery; for flushing out salt residues after replenishing the salt reservoir; includes glass care system; not suitable for tablet detergents. - Page 55 Programme chart Programme sequence Consumption Duration Energy Water Pre- Main Interim Final Drying Cold Litres Cold wash wash rinse rinse water water water water °C °C connec- connec- connec- connec- tion tion tion tion (15 °C) (55 °C) (15 °C) (55 °C) h:min h:min...
-
Page 56: After Sales Service
– Your Miele dealer, or technology. – the Miele Service Department (see Information regarding programme back cover for address). updates will be made known by the Miele Company as and when such Please note that telephone calls may developments become available. -
Page 57: Optional Accessories
Optional accessories To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, the Spare Parts Department or online at www.miele-shop.com (some may be supplied as standard, depending on model). If you would like to …... -
Page 58: Electrical Connection
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 The fuse cover must be refitted when All electrical work must be changing the fuse, and if the fuse cover carried out by a suitably qualified is lost, the plug must not be used until a and competent person, in suitable replacement is obtained. -
Page 59: Plumbing
30 and 1000 kPa (0.3 and 10 bar). Providing your dishwasher has been If the water pressure is too high, a installed correctly, the Miele waterproof pressure reducer valve must be anti-leak system will protect you from fitted. water damage throughout its lifetime. -
Page 60: Drainage
Plumbing Drainage Venting the drainage system – The appliance drainage system is If the on-site drain connection is fitted with a non-return valve, which situated lower than the guide path for prevents dirty water from flowing the bottom basket rollers in the open back into the dishwasher via the door, the drainage system must be drain hose. -
Page 61: Technical Data
Technical data Dishwasher model G 1XXX G 2XXX Height freestanding 84.5 cm (adjustable +3.5 cm) Height built-in 80.5 cm 84.5 cm (adjustable + 6.5 cm) (adjustable + 6.5 cm) Height of building-in Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) recess Width 59.8 cm... - Page 64 Alteration rights reserved/ M.-Nr. 07 329 170 / 00 G1143/G1153/G/G2143/G2153 / 2208...