Advertisement
Quick Links
1
DELL C5522QT
1. Disassembly Procedures:
Remove 6pcs carton locks, then use a proper tool to
open the carton, and then uplift the top paper-box
slowly. Remove EPS-Top(right and left ) with PC box
and accessories box(1pcs Type-C cable, 1pcs HDMI
S1
cable, 1pcs DP cable, 1pcs USB cable, 1pcs
EU+USA cable, battery, remote control, 1pcs cable
lock, 2pcs stylus, stylus magnet, 2pcs tips of pen,
the CD and user's manual).
PC box
Tear off the caution sheet, then take out 3pcs
desiccant bags from the EPS-bottom. Remove the
S2
PE bag from top to bottom. Use a machine jip to
take out the whole monitor from the EPS-bottom,
and then put the monitor on ESD protection foam.
accessories box
Use a screwdriver to
releasing the
handles.
S3
Remove 57pcs screws for unlocking the rear cover
with the assembled unit.(
Remove the handles and rear cover, then use a
S4
screwdriver to remove 7pcs screws for releasing the
PC
box.(Torque: 4.5±0.3kgf)
Tear off 1pcs conductive tape for releasing main
board, USB board and LVDS cable. Remove 2pcs
S5
white mylar tapes.
Remove 5pcs white tapes, 2pcs big black wire locks,
S6
2pcs small black wire locks and 6pcs white wire locks
for unfixing the cables as the picture below shown.
remove 8pcs screws for
(Torque:15±0.5kgf)
Torque: 3±0.3kgf)
Advertisement
Related Manuals for Dell C5522QT
Summary of Contents for Dell C5522QT
- Page 1 DELL C5522QT 1. Disassembly Procedures: Use a screwdriver to remove 8pcs screws for releasing the handles. (Torque:15±0.5kgf) Remove 6pcs carton locks, then use a proper tool to Remove 57pcs screws for unlocking the rear cover open the carton, and then uplift the top paper-box with the assembled unit.(...
- Page 2 DELL C5522QT Disconnect all the cables as the picture below shown. Use a screwdriver to remove 30pcs screws Use a screwdriver to remove 2pcs screws for (left: 5pcs, right :5pcs, top: 10pcs, bottom: 10pcs) for unlocking 4pcs strips, then tear off 4pcs shading unlocking AC power outlet.(Torque: 4.5±0.5kgf)
- Page 3 DELL C5522QT Use a screwdriver to remove 17pcs(11+6) screws (Torque:6±0.3kgf) for unlocking the ED holder with the assembled unit. Tear off 2pcs shading mylar tape for releasing the wire hole of the lighter bar. Turn over the panel module with the bracket for screen faced up. Use a...
- Page 4 DELL C5522QT Remove 1pcs DEBF film, 1pcs Diffuser film, 1pcs Use a tripper to lift up the unit, then use a LGP, 1pcs Reflector film away from the back screwdriver to remove 13pcs screws for unlocking bracket. the ED unit , then use the tripper to put down the unit.
- Page 5 DELL C5522QT S25-4 Take out bulk cap. pin solder with soldering iron and Remove electrolyte capacitors (red mark) from absorber. printed circuit boards. S25-1 Cut the glue between bulk cap. and PCB with a knife. S25-5 Lift the bulk cap. up and away from the PCB.
- Page 6 DELL C5522QT 2. Product material information The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC. Capacitors / condensers (containing No used PCB/PCT) Mercury containing components...