Related Manuals for Miele T 224
Summary of Contents for Miele T 224
- Page 1 Operating instructions for vented tumble dryer T 224 To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 06 465 680...
-
Page 2: Caring For The Environment
To avoid unnecessarily long drying bags etc. are disposed of safely and times and high consumption of energy: kept out of the reach of babies and young children. Danger of suffocation! – Make sure that your laundry is thoroughly spun before drying. -
Page 3: Table Of Contents
Low temperature..........12 Changing the programme sequence........13 Programme chart . - Page 4 Calculating the effective duct length: ........29...
-
Page 5: Warning And Safety Instructions
The manufacturer cannot be increasingly available on the market. If held liable for the consequences of an using, do so at your own risk, and inadequate earthing system (e.g. follow the instructions provided on the electric shock). - Page 6 Repairs should only be undertaken by a Miele approved technician. Ensure current is not supplied to the machine until after maintenance or repair work has been carried out. Faulty components must only be replaced by genuine Miele original spare parts.
- Page 7 (e.g. gas, oil or coal fired heater, continuous flow – it is switched off at the wall socket or other water heater) is installed in the and the plug is withdrawn, or same or an adjacent room.
- Page 8 Do not allow children to play on or near it or to play with its controls. Supervise – items which contain damaged its use by the elderly or infirm.
-
Page 9: Control Panel
PC indicator light d I-On/0-Off button The indicator light marked PC is used by Miele Service technicians as an To switch the machine on or off / to optical interface. interrupt a programme. The Anti-crease/Finish lamp will light up as confirmation that the machine... -
Page 10: Notes On Laundry Care
..Dry at a low temperature dried if specified as suitable by the s ....Do not tumble dry manufacturer on the care label, as –... -
Page 11: How To Dry Correctly
^ Press the Door button to open the The headings numbered (A, B, C ...) show the operating sequence and can door. be used as a brief guide to using your ^ Load the laundry loosely into the machine. drum. -
Page 12: Low Temperature
Woollens handcare programme. During the anti-crease phase ..(depending on the programme selected) the indicator lamp for the drying stage reached will also light up..the buzzer will sound at intervals. -
Page 13: Changing The Programme Sequence
^ Remove the laundry. ^ Turn the programme selector to Finish or open the door . Make sure that the drum is empty. If items are left in the dryer, they could Adding or removing laundry after a be damaged by overdrying when programme has started the dryer is next used. -
Page 14: Programme Chart
Fabric Cottons and linen fabrics, e.g. table linen, bedlinen, starched laundry. type Note To prevent laundry from drying out it should be rolled up until you are ready for ironing. Minimum iron Max. load: 3 kg* Normal**, Low temperature, Hand iron Fabric Minimum iron items made of cotton, synthetic or blended fabrics, e.g. - Page 15 Max. load: 3 kg* Fabric – Cottons and linen fabrics. type – Minimum iron items made of mixed fibres, cottons or synthetics e.g. trousers, jackets, shirts. Notes – Smooths out creasing caused during the spin cycle in the washing machine.
-
Page 16: Cleaning And Care
Miele Spare Parts Department. every drying cycle. You can also use a vacuum cleaner. ^ Also clean the door seal (2) with a damp cloth. If there is a great deal of compacted fluff on the filter, it can be cleaned under running water. -
Page 17: Tumble Dryer
These could damage plastic surfaces and other parts. The machine must never be hosed down. ^ Dry all parts with a soft cloth. E-Cloth A microfibre "E-Cloth" is available from the Miele UK Spare Parts Department, which is suitable for cleaning surfaces... -
Page 18: Problem Solving Guide
Problem solving guide With the help of the following notes minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department. Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with local and national safety regulations. - Page 19 Problem solving guide Problem Possible cause Remedy There is a build Fluff is principally the result of Fluff is collected by the fluff up of fluff. friction when garments are filter and can be easily being worn and washed. removed (see "Cleaning and Machine drying hardly Care").
- Page 20 Remedy The drying Important: Before attempting to remedy one of the following process goes on causes, switch the dryer off and switch on again to start the too long or even programme again. switches off. Ventilation to the dryer is Open a door or window while insufficient (e.g.
-
Page 21: Check And Fault Indicator Lamps
The programme has No obvious cause. – Switch the dryer off and been interrupted. The then on again. indicator lamp for – Then start the Hand iron or Machine programme again. -
Page 22: Changing The Lamp
^ To close the cover push it upwards You will find the interior lamp cover at the top of the drum aperture. and press it on the left and right until you hear it click into position. Ensure that it is fitted into position securely, as any moisture could cause a short circuit. -
Page 23: After Sales Service
After sales service Repairs Appliance guarantee In the event of any faults which you Please see the guarantee card cannot remedy yourself, or if the supplied with your machine. machine is under guarantee, please contact Optional accessories – your Miele dealer, or... -
Page 24: Installation And Connection
Installation and connection Front view a Venting connection: rear, right or left (supplied with the rear socket open) b Mains connection cable c Control panel d Door e Four height adjustable screw feet... -
Page 25: Installation Site
* Available as an optional accessory from your Miele dealer or the Miele When moving the machine you can hold it by the lid where it protrudes to Spare Parts Department. the rear of the dryer. To manoeuvre the If you wish to push your machine under... -
Page 26: Levelling The Machine
* Available as an optional accessory from your Miele dealer or the Miele Spare Parts Department. Stacking kits must only be installed by a suitably qualified fitter. ^ The screw feet can be adjusted to compensate for any unevenness in the floor. -
Page 27: Electrical Connection
The regulations (BS 7671 in the UK). -
Page 28: Installation - Venting
– for venting to the outside: connected to the power supply. a wall pipe kit* or a window vent kit*. – The ducting outlet (e.g. wall pipe) * Available as an optional accessory should be installed in such a way from your Miele dealer or the Miele that the moist expelled air . -
Page 29: Calculating The Effective Duct Length
1 metre of Flexible aluminium ducting* / plastic straight plastic piping (Table I). piping – 1 m laid straight / or 1 m straight 1.0 m The additional duct length factor for pipe each item needs to be added together –... -
Page 30: Installation To The Left Or Right Side Of The Machine
Result: A duct diameter of 100 mm is that it cannot fall out when the dryer adequate as the effective duct length is is in operation. less than the 20 m specified in Table II. ^ Fit one of the venting systems described on the following pages. -
Page 31: Adapter
^ The following items are required: ... flexible ducting hose ... a wall vent kit* or window vent kit*. * (Miele optional accessory). A ring adapter** (1) is installed in adapter (2) for the installation of a flexible vent duct. - Page 32 3. Exhaust flue insulated against damp kit) The ducting must not be vented 2. Adapter for flexible hose into a chimney or vent flue which is in use, nor should it be connected to ducting which ventilates rooms with fireplaces.
-
Page 33: Venting System With Plastic Piping
^ The following items are required: ..an adapter* (dia. 100 mm)* with rib on the inside..a wall vent kit* or window vent kit*. * (Miele optional accessory) . . . Suitable plastic piping is available from your dealer or builder’s... -
Page 34: Connecting Directly To A Wall Vent
^ A wall pipe and a flexible foam gasket must be used (both Miele optional accessories). A Before drilling into the wall . . . 1. Wall pipe . . . please read the installation 2. Flexible foam gasket instructions supplied with the Miele wall pipe. -
Page 35: Washer Dryer Stack
Installation - venting Washer dryer stack Miele washing machine with Comfort line angled fascia Height of venting outlet for washer dryer stack Miele washing machine with straight or sloping fascia Stacking kit* without pull-out shelf: C = 94.2 cm D = 170.0 cm... -
Page 36: Consumption Data
** EN 61121 Standard testing is carried out with the ring adapter. All data established in accordance with EN 61121. Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual moisture as per the above standard using the Cottons Normal programme. -
Page 37: Technical Data
Technical data Height 850 mm (adjustable +7 / -7 mm) Height for building under 820 mm Width 595 mm Depth 580 mm Depth with door open 1,060 mm Weight 48 kg Drum volume 100 litres Maximum capacity 6 kg dry weight... - Page 39 Programmable functions for changing default settings The programmable functions are used to alter the machine's electronics to suit changing requirements. Programmable functions can be altered at any time.
-
Page 40: Programmable Functions
. . . However, if you require the laundry to be drier, it is possible to reduce the D . . . and then release the Start button. default residual moisture level in the E Turn the programme selector to the Cottons programmes. -
Page 41: Altering The Residual Moisture Level In The Minimum Iron Programmes
. . . However, if you require the laundry to be drier, it is possible to reduce the D . . . and then release the Start button. default residual moisture level in the E Turn the programme selector to the Minimum iron programmes. -
Page 42: Activating And Deactivating The Buzzer
The machine is delivered with the comes on . . . buzzer activated but you can D . . . and then release the Start button. deactivate it if wished. E Turn the programme selector to the The buzzer will still sound if there is a Cottons Hand iron position. -
Page 43: Extending The Cooling Down Time
I-On/0-Off button. C Wait until the Start indicator lamp comes on . . . D . . . and then release the Start button. E Turn the programme selector to the Cottons Machine iron position. F Pressing the Start button alters the... -
Page 44: Changing The Standard Drying Level In The Minimum Iron - Normal Programme
B Switch the dryer on with the I-On/0-Off button. C Wait until the Start indicator lamp comes on . . . D . . . and then release the Start button. E Turn the programme selector to Minimum iron - Normal . -
Page 45: Changing The Standard Drying Level In The Automatic Programme
C Wait until the Start indicator lamp ^ Switch off the dryer. comes on . . . The check is complete. D . . . and then release the Start button. E Turn the programme selector to the Automatic position. - Page 48 Alteration rights reserved/1306 M.-Nr. 06 465 680 / 01 en - GB...