Table of contents Safety .......... 4 Folding prongs ....... 23 General information...... 4 Extra Clean Zone ...... 23 Intended use........ 4 Basket heights........ 24 Restriction on user group.... 4 Before using for the first time .. 25 Safe installation ........ 4 Performing the initial configura- Safe use ........... 6 tion.......... 25 Damaged appliance ...... 8...
Page 3
Customer Service...... 57 Terminate programme.... 34 Product number (E-Nr.), produc- Switching off appliance .... 34 tion number (FD) and consecut- Basic settings........ 35 ive numbering (Z-Nr.) ..... 57 Overview of basic settings ..... 35 AQUA-STOP guarantee .... 58 Changing basic settings.... 36 Technical specifications.... 58 Home Connect ......
en Safety Safety Observe the following safety instructions. General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. Intended use Only use this appliance: ¡...
Page 5
Safety en WARNING ‒ Risk of electric shock! ¡ Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing.
en Safety ¡ Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. ▶...
Page 7
Safety en WARNING ‒ Risk of injury! ¡ Leaving the appliance door open may result in injury. ▶ Only open the appliance door to load or unload tableware in order to prevent accidents, e.g. through tripping. ▶ Do not sit or stand on the appliance door when open. ¡...
en Safety Damaged appliance WARNING ‒ Risk of electric shock! ¡ If the appliance or the power cord is damaged, this is danger- ous. ▶ Never operate a damaged appliance. ▶ Never operate an appliance with a cracked or fractured sur- face. ▶ Never pull on the power cord to unplug the appliance. Al- ways unplug the appliance at the mains.
Page 9
Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. ▶ With redundant appliances, unplug the power cord. Then cut through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close.
en Preventing material damage pipes supplied for the drinking Preventing material damage Preventing material dam- water and waste water connec- tions are not affected here. ¡ Modified or damaged water hoses may result in material damage and Preventing material damage Safe installation damage to the appliance.
Environmental protection and saving energy en ¡ Unsuitable cleaning agents may AquaSensor damage the appliance. The AquaSensor is an optical meas- Do not use a steam cleaner. ▶ uring device (light barrier) which So as not to scratch the finish ▶ measures the turbidity of the rinsing on the appliance, do not use water.
en Installation and connection walls. If you subsequently install your Sensor setting Description dishwasher as a free-standing appli- ing low levels of active ance, you must stop it from tipping agents. Energy and water over, e.g. by screwing it to the wall or consumption are adjusted installing it under a continuous work- accordingly.
Installation and connection en Also check that there is no cover The connection data for the appli- in the drainage system preventing ance can be found on the rating the wastewater from being dis- plate. charged. Check that the mains plug is inser- ted properly.
en Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with "E number and FD number" → Page 57.
Familiarising yourself with your appliance en "Detergent" → Page 28 is added to the detergent Detergent dispenser dispenser. "Bottom basket" → Page 22 Bottom basket Dispenser for special salt Add special salt to the dispenser for special salt. → "Water softening system", Page 25 Lower spray arm The lower spray arm washes the tableware in the bot- tom basket.
Page 16
en Familiarising yourself with your appliance "Switching on the appliance" → Page 33 ON/OFF button and reset button "Switching off the appliance" → Page 34 "Terminating the programme" → Page 34 "Programmes" → Page 18 Programme buttons Programme sequence display The programme sequence display shows the cur- rent cycle of the appliance, e.g. washing, rinsing or drying.
Page 17
Familiarising yourself with your appliance en Rinse aid refill indicator Rinse aid system → "Adding rinse aid", Page 27 Water supply display Display for water supply Special salt refill indicator Water softening system → "Adding special salt", Page 26 Door handle Open the appliance door. Depending on the appliance specifications...
en Programmes Programmes Programmes You can find an overview of the pro- runtime will change if the rinse aid Programmes grammes that can be selected here. system is switched off or rinse aid Different programmes, which can be needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
Page 19
Programmes en Programme: Programme sequence Additional func- tions Tableware: Reduced noise: → "Additional ¡ Cleaning mixed table- ¡ Pre-Rinse Silence 50 ware and cutlery. functions", ¡ Cleaning 50 °C Level of soiling: Page 20 ¡ Intermediate rinse ¡ Removing common ¡ Final rinse 65 °C household food remnants ¡...
en Additional functions Press for 3 seconds. Information for test institutes a The selected programme and the Test institutes are provided with in- additional function will flash. formation for comparability tests, e.g. flashes. according to EN60436. a The programme and the additional These are the conditions for conduct- function are saved.
Features en Top basket Additional func- tion Arrange cups, glasses and small ¡ Switch on with mixed items of tableware in the top basket. loads containing table- IntensiveZone ware with different soil- ing levels, e.g. place very soiled pots and pans in the bottom bas- ket and normally soiled tableware in the upper basket.
en Features Raise or lower the basket evenly to the right level. Cutlery drawer Check that the basket is level on Arrange cutlery in the cutlery drawer. both sides. Release the levers. a The basket clicks into position. Slide the basket back in. Bottom basket Arrange pans and plates in the bot- tom basket.
Features en Push the lever forwards and fold Etagere down the prongs . Use the cutlery shelf and space un- derneath for small cups and glasses or for large items of cutlery, e.g. cooking spoons or serving cutlery. To use the prongs again, fold them back up.
en Features Set the slider to ON or OFF. Pull the tab on the Extra Clean Zone up and forwards . Push in the top basket. Set the slider to ON. Cleaning Extra Clean Zone Clean under running water. Limescale and soiling from the dish- Place the Extra Clean Zone in the washing water can block the nozzles.
Before using for the first time en "Set the amount of rinse aid to be Before using for the first time Before using for the dispensed." → Page 28 first time "Add detergent" → Page 28. Start the Programme with the Before using for the first time highest cleaning temperature Performing the initial config- without tableware.
en Water softening system Note: Set the water hardness determ- ATTENTION! ined on your appliance. ¡ Detergent may damage the water softening system. → "Setting the water softening sys- tem", Page 26 Only fill the dispenser of the wa- ▶ ter softening system with special With a water hardness of 0 - 8 °E you can dispense with special salt for dishwasher salt.
Rinse aid system en Adding rinse aid Switching off the water If the rinse aid refill indicator lights softening system up, top up with rinse aid. Only use If you find the special salt refill indic- rinse aid for domestic dishwashers. ator irritating, e.g.
en Detergent Press repeatedly until Setting the amount of rinse the display shows the value set at the factory r:05. If there are streaks or water marks on Press repeatedly until the tableware, change the amount of display shows r:00. rinse aid. To save the settings, press for 3 seconds.
Detergent en Combined detergent Detergent Description Besides conventional separate deter- Powder deter- Powder detergent is re- gents, a number of products are gent commended for shorter available with additional functions. "Programmes" → Page 18. These products contain not only de- The dosage can be adjus- tergent but also rinse aid and salt re- ted to the level of soiling.
en Detergent pletely dispense with certain sub- Add the detergent to the dry deter- stances. The cleaning effect may gent dispenser. be restricted here. ¡ Set the rinse aid and the water 50 ml softening system to the separate 25 ml detergent or combined detergent 15 ml in use.
Tableware en Close the lid of the detergent dis- Damage to glass and table- penser. ware Only put glasses and china in the dishwasher if it is marked as dish- washer-safe by the manufacturer. Avoid damage to glass and table- ware. Cause Recommendation The following table-...
en Tableware To save resources, do not pre- Cause Recommendation rinse tableware under running wa- The water temperat- Select a programme ter. ure of the programme with lower temperat- Observe the following when arran- is too high. ures. ging tableware: After the programme –...
Basic operation en Removing tableware Setting additional functions You can set additional functions to WARNING complete the washing programme Risk of injury! selected. Hot tableware can cause burns to the Note: The additional functions which skin. When hot, tableware is sensitive can be used depend on the pro- to shock, may crack and can result in gramme selected.
en Basic operation ¡ You can only change a pro- Terminate programme gramme when running if you can- To end a programme early or to cel it. switch from a programme that has → "Terminate programme", already started, you will need to can- Page 34 cel it first.
Basic settings en Basic settings Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings Overview of basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H:04...
en Basic settings Basic setting Display text Selection Description Tone volume SL:02 SL:00 -SL:03 Adjustment of tone volume. Level "SL:00" switches the signal tone off. Button volume bL:02 bL:00 - bL:03 Set the button volume during opera- tion. Level "bL:00" switches the but- ton tones off.
Home Connect en Home Connect quick start Home Connect Home Connect Connect your appliance to a mobile This appliance is network-capable. Home Connect device quickly and easily. Connect your appliance to a mobile Installing app device to control its functions via the Home Connect app. Install the Home Connect app on The Home Connect services are not your mobile device.
en Home Connect Home Connect settings Remote Diagnostics Adapt Home Connect to your needs. Customer Service can use Remote You can find the Home Connect set- Diagnostics to access your appliance tings in the basic settings for your ap- if you contact them, have your appli- pliance.
Tip: You can get our tested and ap- proved Dishwasher Care and Ma- WARNING chine Cleaner for Dishwashers online Risk of harm to health! at https://www.bosch-home.com/ Using detergents containing chlorine store or from customer service. may result in harm to health. Never use detergents containing Tips on appliance care ▶...
Page 40
Dishwasher Care and Ma- ular intervals. chine Cleaner for Dishwashers online Machine Care combined with ma- at https://www.bosch-home.com/ chine care products and machine store or from customer service. cleaners is the right programme for Machine Care is a programme which the care of your appliance.
Cleaning and servicing en a Machine Care is run. Turn the coarse filter anticlockwise a Once the programme has ended, and remove the filter system . the indicator for Machine Care Check that no foreign objects ‒ goes out. fall into the sump. Filter system The filter system removes coarse soiling from the dishwashing cycle.
en Cleaning and servicing Carefully clean the rim of dirt Pull up the lower spray arm to re- between the coarse and the fine fil- move. ter. Re-assemble the filter system. Make sure that the locking catches on the coarse filter click into posi- tion.
Troubleshooting en Troubleshooting Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶...
Page 44
en Troubleshooting Fault Cause Troubleshooting E:32-00 will light up altern- Remove the filter from the supply ately or indicator for water hose supply lights up. Clean the filter. Re-insert the filter in the supply hose. Screw the water connection back Check the water connection for leaks.
Troubleshooting en Fault Cause Troubleshooting E:90-01 will light up altern- Mains voltage is too low. This is not a fault on the appliance. ately. Contact an electrician. Have the mains voltage and elec- trical installation checked by an electrician. E:92-40 will light up altern- Filters are soiled or blocked.
Page 46
en Troubleshooting Fault Cause Troubleshooting Tableware is not dry. Water collects in recesses of Position tableware at an angle ▶ the tableware or cutlery. where possible. The combined detergent Use rinse aid to improve drying per- used has a poor drying per- formance.
Page 47
Troubleshooting en Fault Cause Troubleshooting Remnants of food on table- Tableware is placed too Arrange tableware with sufficient ware. close together or basket is space in between. overfilled. The spray jets must reach the sur- faces of the tableware. Avoid points of contact. Spray arm rotation is Arrange tableware so that it does ▶...
Page 48
en Troubleshooting Fault Cause Troubleshooting Detergent residue in the ap- Tabs are used in the quick Select a more intensive "Pro- ▶ gramme" → Page 18 or use pliance or short programme. Dissolv- "Powder detergent" → Page 28. ing time of the tab is not at- tained.
Page 49
Troubleshooting en Fault Cause Troubleshooting Stubborn white coatings are Too little detergent is being Increase the amount of detergent ▶ present on tableware, inside used. used or change "Detergent " → Page 28. the appliance or the door. Washing programme selec- Select a more intensive washing ▶...
Page 50
en Troubleshooting Fault Cause Troubleshooting Coloured deposits (yellow, The formation of films is due Check the setting of the water orange, brown) that are easy to ingredients of food rem- softening system. to remove are present inside nants and tap water (limes- Add special salt.
Page 51
Troubleshooting en Fault Cause Troubleshooting Irreversible clouding of Glasses are not dishwasher- Use dishwasher-proof glasses. ▶ glassware. proof, only suitable for dish- Glasses are usually only suitable for washers. use in a dishwasher, i.e. long-term wear or long-term changes must be expected.
en Troubleshooting Home Connect problem Fault Cause Troubleshooting Connection to home net- WLAN on router is not act- Check the wireless network con- ▶ work is not established. ive. nection of your router. WLAN display is flashing. Connection to home net- Activate the wireless network con- ▶...
Page 53
Troubleshooting en Fault Cause Troubleshooting Appliance cannot be Appliance functions have Pull out the mains plug or switch off switched on or operated. failed. the fuse. Wait at least 2 minutes. Connect the appliance to the power supply. Switch the appliance on. Appliance does not start.
en Troubleshooting Fault Cause Troubleshooting All LEDs lit up or flashing. Electronics have detected a Press the main switch button for ap- fault. prox. 4 seconds. → "Controls", Page 15 The appliance is reset and restar- ted. If the problem occurs again: Switch off the appliance. ‒...
Page 55
Troubleshooting en Fault Cause Troubleshooting Knocking or rattling noise. With a small load the water Distribute the tableware evenly. ▶ jets directly strike against Load the appliance with more table- ▶ the tub. ware. Light items of tableware Position light items of tableware se- ▶...
en Transportation, storage and disposal Insert the pump cover and press Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned.
Customer Service en Unplug the appliance from the Transporting the appliance mains. To avoid damage to the appliance, Cut through the power cord. empty it before transporting. Dispose of the appliance in an en- Note: Always transport the dish- vironmentally friendly manner. washer upright to prevent residual Information about current disposal water getting into the machine's con-...
en Technical specifications Make a note of your appliance's de- Voltage 220 - 240 V, 50 Hz or tails and the Customer Service tele- 60 Hz phone number to find them again Power rating 2000 - 2400 W quickly. Fuse 10 - 16A AQUA-STOP guarantee Water pressure ¡...
A detailed RED Declaration of Con- offer support and spare parts for the formity can be found online at relevant appliance. www.bosch-home.com among the additional documents on the product page for your appliance. Declaration of Conformity Declaration of Conformity BSH Hausgeräte GmbH hereby de-...
Page 60
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.