hit counter code
Download
Share
Print this page
Lenovo S660 Service Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Cell Phone
  5. S660
  6. Service manual

Lenovo S660 Service Manual

Hide thumbs Also See for S660:

Advertisement

Quick Links

Download this manual
Company confdentaa
Lenovo S660 Service Manual
Lenovo S660 Service Manual
Publisher ： NJD HW Team
Date ： 2014.02.28

Advertisement

loading

Related Manuals for Lenovo S660

Summary of Contents for Lenovo S660

  • Page 1 Company confdentaa Lenovo S660 Service Manual Lenovo S660 Service Manual Publisher ： NJD HW Team Date ： 2014.02.28...

  • Page 2: Function Block

    Function Block Function Block Company confdentaa...
  • Page 3 M/B Top Placement #1 M/B Top Placement #1 Receiver Audio Jack crystal SKY77593 MT6166 FLASH Backlig ht IC MT6582 MT6627 Charge MB to SB connector Company confdentaa...
  • Page 4 M/B Bottom Placement #2 M/B Bottom Placement #2 Connector Sensor G-Sensor Connector Mic 2 Audi o PA BACK UP BATTERY Camera Connector DUAL SIM CONNECTOR crystal TF CARD CONNECTOR connector MT6323 Battery connector Company confdentaa...
  • Page 5 BB Common Question BB Common Question • BB-1 Power on failure ( 無法開機 ) • BB-2 Firmware update failure ( 無法更新軟件 ) • BB-3 Charging failure ( 無法充電 ) • BB-4 SIM Card identified error (SIM 卡無法識別 ) • BB-5 LCD display error ( 畫面無法顯示或顯示異常 ) •...
  • Page 6 無法開機 無法開機 BB-1 Can not power on ( ) (1/3) BB-1 Can not power on ( ) (1/3) 1. Check if battery power level is low ( 確認電池是否有電 ?) • – VBATT (TP09 > 3.6V) 2. Check if J802 soldering condition is good ( 確認 J802 吃錫狀況是否正常 ?) •...
  • Page 7 無法開機 無法開機 BB-1 Can not power on ( ) (2/3) BB-1 Can not power on ( ) (2/3) 5. Please check whether MT6323 voltage is normal ( 請確認 MT6323 周圍電壓是否正常 ?) • – VPROC_PMU should be between C134 (0.9V~1.1V) – VSYS_PMU should at R373 (1.8V) VPROC_PMU VSYS_PMU Company confdentaa...
  • Page 8 無法開機 無法開機 BB-1 Can not power on ( ) (3/3) BB-1 Can not power on ( ) (3/3) MT6323 Power On/Off sequence VCORE≈0.7V~1.3V VPORC≈0.7V~1.3V VIO18=1.8V VIO28=2.8V VM12_INT=1.2V VA1=2.5V VA2=2.5V VUSB=3.3V VTCXO=2.8V VMC=3.3V VMCH=3.3V RESET=1.8V Company confdentaa...
  • Page 9 無法更新軟件 無法更新軟件 BB-2 Can not download ( ) (1/3) BB-2 Can not download ( ) (1/3) 1. Please check whether current is normal after boot ( 確認開機後電流起跳正常 ) • ( 記憶體中無代碼時，電池電流約在 0.1A 左右 ) • • 2. If current in booting process is larger or less than normal, USB port will be unidentified ( 開機過程中如果電流過大或過小，會造成...
  • Page 10 無法更新軟件 無法更新軟件 BB-2 Can not download ( ) (2/3) BB-2 Can not download ( ) (2/3) • 4. If DL is passed, and META mode is un-entered, check RF transceiver 26MHz and RF chip function ( 若可以正常 DL ，但無法進入 META mode ，檢查 RF transceiver 26MHz 及 RF chip 是否 正常。...
  • Page 11 無法更新軟件 無法更新軟件 BB-2 Can not download ( ) (3/3) BB-2 Can not download ( ) (3/3) 5. Check if com port is correct ( 確認 com port 是否正確 ) • Company confdentaa...
  • Page 12 無法充電 無法充電 BB-3 Can not charging ( ) (1/2) BB-3 Can not charging ( ) (1/2) • 1. Check if battery resistance R332 Pin1(BAT_ID) is 10kΩ when battery is installed ( 確認電池內阻 R332 Pin1 (BAT_ID) ， 當接上電 池後阻抗應該約 10kΩ.) 2. Check battery voltage, if 0V reveals open circuit ( 確認電池電壓 •...
  • Page 13 無法充電 無法充電 BB-3 Can not charging ( ) (2/2) BB-3 Can not charging ( ) (2/2) 4. Check charging IC and related circuit soldering condition is good ( 確認充電 • IC 及周围电路焊接是否正常。 ) – When USB port has be inserted, VBUS should be at 5V output (VBUS 在 USB 插入時，是否有...
  • Page 14 卡無法識別 卡無法識別 BB-4 SIM Card Identification error (SIM ) (1/2) BB-4 SIM Card Identification error (SIM ) (1/2) 1. Check if SIM Card is in normal condition ( 更換 SIM 卡，確認卡片是否正常 ?) • 2. Check if J3200 soldering condition is normal ( 確認 J3200 吃錫狀況是否正常 ?) •...
  • Page 15 卡無法識別 卡無法識別 BB-4 SIM Card Identification error (SIM ) (2/2) BB-4 SIM Card Identification error (SIM ) (2/2) SIM1/SIM2 的供电电 压各来自 PMU 的两 组 LDO output SIM1/SIM2 output voltage are coming from two LDO output of PMU SIM1 和 SIM2 的 DATA/RST/CLOC K 单独分开使用...
  • Page 16 畫面無法顯示或顯示異常 畫面無法顯示或顯示異常 BB-5 Can not display ( BB-5 Can not display ( 1. Check J904 soldering condition ( 確認 J904 是否有異狀 [ 鍚短 or 空焊 ]?) • 2. Replace LCD ( 更換 LCM) • If failure still exists after LCM replacement ( 若更換良品後，現象還存在 ) •...
  • Page 17 感測器不良 感測器不良 BB-6 sensor function fail ( ) (1/2) BB-6 sensor function fail ( ) (1/2) 所有的 sensor 都是由 I2C 總線，中斷信號，電源組成 .I2C 總線上 sensor 間會相互影 • 響，所以維修某個 sensor 不良時需要同步檢查其他 sensor 路徑。 • All sensors are consisted by I2C bus, interrupt signal and power. Sensors on I2C bus are affected by each other, therefore related sensors checking is needed when repairing sensor.
  • Page 18 感測器不良 感測器不良 BB-6 sensor function fail ( ) (2/2) BB-6 sensor function fail ( ) (2/2) G-sensor I2C 通過上拉電阻連接到 CPU ，此 I2C 與 touch panel 共 用， VDD18_PMU 異常會造成所有 sensor fail 。 G-sensor I2C connect to CPU with Pull-up resistor, which share with touch panel, VDD18_PMU error will lead to all sensors failure.
  • Page 19 無法觸屏 無法觸屏 BB-7 Touch Panel no function ( ) (1/2) BB-7 Touch Panel no function ( ) (1/2) 1. Check if TP connector is loosen ( 確認 TP Connector 是否鬆脫 ?) • 2. Replace TP ( 更換 TP) • If failure still exists after TP replacement ( 若更換後良品後，現象還存在 ) •...
  • Page 20 無法觸屏 無法觸屏 BB-7 Touch Panel no function ( ) (2/2) BB-7 Touch Panel no function ( ) (2/2) • TP circuit 復位信號 Reset Signal TP 工作電壓 2.8V/1.8V TP Working Voltage 2.8v/1.8v Company confdentaa...
  • Page 21 馬達無振動 馬達無振動 BB-8 Vibrator no function ( BB-8 Vibrator no function ( 1. Check if motor is in normal condition (Resistance is 30Ω) ( 確認馬達是否正常 • ( 馬達阻抗約 30Ω)) 2. Check if motor soldering condition ( 確認馬達是否有異狀 [ 鍚短 or 空焊 ]?) •...
  • Page 22 無法攝像 無法攝像 BB-9 Camera can not turn on ( ) (1/4) BB-9 Camera can not turn on ( ) (1/4) 1. Check camera module has been well assembled ( 確認組裝是否到位 ?) • 2. Replace camera module ( 更換 camera module) •...
  • Page 23 無法攝像 無法攝像 BB-9 Camera can not turn on ( ) (2/4) BB-9 Camera can not turn on ( ) (2/4) 主 camera 的 4 組工作電壓均是由 PMU LDO 輸出通過給 camera • • All 4 working voltage of main camera are inputted from PMU LDO Camera 源頭路徑...
  • Page 24 無法攝像 無法攝像 BB-9 Camera can not turn on ( ) (3/4) BB-9 Camera can not turn on ( ) (3/4) 1: 無法進入拍攝模式 , 此為 camera 無法通過 I2C 信 • 號被 CPU 正常識別造成 , 此不良主要查供 電 /reset/CLK/PWD 是否正常 • 1. Camera shooting model is not accessible. The main cause is camera cannot be identified by CPU via I2C, need to check power supply for camera.
  • Page 25 無法攝像 無法攝像 BB-9 Camera can not turn on ( ) (4/4) BB-9 Camera can not turn on ( ) (4/4) VREF/HREF: Sensor 垂直 / 水平參考信號 Sensor reference of horizon and vertical MCLK: 來自 CPU 的主時鐘輸出 Main clock from CPU PCLK: 象數時鐘輸入 Clock input from image-numerology Company confdentaa...
  • Page 26 麥克風無作用 麥克風無作用 BB-10 MIC no function ( BB-10 MIC no function ( 1. 確認 J1003 Microphone 是否正常 ( 正常 Mic 阻抗約 0.95KΩ) • – Check if J1003 Microphone is in normal condition, MIC resistance should be at 0.95KΩ. 2. 確認 MIC 周邊電路是否有異狀 [ 鍚短 or 空焊 ]? •...
  • Page 27 喇叭無聲 喇叭無聲 BB-11 Speaker no function ( BB-11 Speaker no function ( 1. 確認 MB to SB FPC 是否連接 ok • • Check MB to SB FPC is well connected 2. 確認 Speaker 彈腳及阻抗是否正常 ( 正常阻抗約 8Ω) • • Check speaker shrapnel and resistance are at normal condition (normal resistance is 8Ω) 3.
  • Page 28 不良 不良 BB-12 Audio function fail (Audio ) (1/4) BB-12 Audio function fail (Audio ) (1/4) Audio 类不良针对不同测试项 fail, 检查不同的路径 . 1:wave play back fail 测的是 SPK 路径 . 2:receiver fail  测的是手机听筒路径 . 3:headset fail  测的是耳机左右声道路径 . 4:phone mic1 to headset fail  测的是手机 MIC1 路径 . 5:phone mic1 to headset fail ...
  • Page 29 不良 不良 BB-12 Audio function fail (Audio ) (1/4) BB-12 Audio function fail (Audio ) (1/4)  Speaker path: PMU 給出 SPK 信號進入 Audio PA 進行放大處理 PMU output SPK signal to Audio PA to amplify Audio PA 輸出放 大后的 SPK 信號 Audio PA output SPK signal after amplifying...
  • Page 30 不良 不良 BB-12 Audio function fail (Audio ) (2/4) BB-12 Audio function fail (Audio ) (2/4) 聽筒無聲 , 優先 check 0om 是否導通  Receiver path: Check 0Com first if receiver is not functional  Phone MIC path PMU 輸出音頻信號 PMU output audio signal 為...
  • Page 31 不良 不良 BB-12 Audio function fail (Audio ) (3/4) BB-12 Audio function fail (Audio ) (3/4)  耳機左右聲道電路 : Earphone L/R channel circuit PMU 輸出耳機音頻信號 耳機左右聲道連接至 audio jack PMU output earphone audio Earphone L/R channel link to audio jack signal 耳機...
  • Page 32 不良 不良 BB-12 Audio function fail (Audio ) (4/4) BB-12 Audio function fail (Audio ) (4/4)  耳機 MIC 電路 Earphone MIC Circuit: 為耳機 MIC 提供偏置電壓 Provide bias votage for earphone MIC 耳機 MIC 信號通過差分電路進入 PMU 作音頻處理 Earphone MIC signal output to PMU to be process by differential circuit Company confdentaa...
  • Page 33 無作用 無作用 BB-13 SD Card no function (SD Card BB-13 SD Card no function (SD Card 1. Check SD card is been inserted properly ( 確認 SD CARD 有確實卡到位 ) • 2. Check SD card related circuit are in good condition ( 確認 SD Card 周邊電路是 •...
  • Page 34 WIFI /BT/GPS WIFI /BT/GPS WIFI/BT/GPS 功能使用的 IC 為 MTK MT6627 WIFI/BT/GPS IC are MTK MT6627 I/Q Signal Connect to CPU MT6582 獨立的 26M TCXO ， Output SCLK,DataSignal Clock to MT6627 Separate 26M TCXO, output clock to MT6627 Company confdentaa...
  • Page 35 WIFI /BT/GPS WIFI /BT/GPS  MT6627 Power Supply Output to MT6627 From PMU MT6323 Company confdentaa...
  • Page 36 GSM PA + S witch GSM PA + S witch Logic controa tabae GSM HB/LB Rx Logic controa signaa WCDMA Band HB/LB TRx GSM Vbat GSM LB Tx input GSM HB Tx input Company confdentaa...
  • Page 37 GSM RX GSM RX GSM HB/LB Circuit: 2G LB Rx Baaance output to transceiver LB Port 2G HB Rx Baaance output to transceiver HB Port Company confdentaa...
  • Page 38 WCDMA B 1/8 TR x (VV36/38) WCDMA B 1/8 TR x (VV36/38) Rx baaance to transceiver TRx connect with ANT Switch Rx baaance to transceiver TRx connect with ANT Switch Band 8 Tx Tx from Transceiver Band 1 Tx Company confdentaa...
  • Page 39 WCDMA B 2/5 TR x (VV37) WCDMA B 2/5 TR x (VV37) Rx baaance to transceiver TRx connect with ANT Switch Rx baaance to transceiver TRx connect with ANT Switch Band 5 Tx Tx from Transceiver Band 2 Tx Company confdentaa...
  • Page 40 RF introduction: MT6166 Function Block RF introduction: MT6166 Function Block Company confdentaa...
  • Page 41 RF introduction: MT6166 Pin assignment RF introduction: MT6166 Pin assignment Company confdentaa...
  • Page 42 RF introduction: Antenna Circuit RF introduction: Antenna Circuit • Antenna Circuit RF 天線主要包含了 2G/3G/WIFI/GPS, 其匹配電路分別描述如下 Main ANT RF Paths RF antenna consists 2G/3G/WIFI/GPS, Description as right diagram WIFI ANT RF Paths Wif /BT path GPS path Company confdentaa...
  • Page 43 RF introduction:2G/3G Main Antenna Position RF introduction:2G/3G Main Antenna Position ANT Matching MB RF Switch Connect to Sub by Coaxial Cable Company confdentaa...
  • Page 44 RF introduction: WIFI Antenna Position RF introduction: WIFI Antenna Position WiFi/BT/GPS WiFi/BT/GPS Antenna Antenna Clips Matching Company confdentaa...
  • Page 45 common issue common issue RF-1:Network function error RF-2:GSM problem RF-3:WCDMA problem RF-4:GSM/WCDMA Rx error RF-5:WIFI problem Company confdentaa...
  • Page 46 RF-1:Network function error RF-1:Network function error • 若 2G/3G 網路功能異常 , 請檢查螢幕天線格數 ,SIM card 是否裝好 ? Coaxial cable 和是否組好 ? • If 2G/3G network is on failure, check reception level on screen, SIM card inserted properly and Coaxial cable connected well. Company confdentaa...
  • Page 47 RF-2:GSM Trouble shooting (1/3) RF-2:GSM Trouble shooting (1/3) • Check GSM transmission path ( 檢查 GSM 發射路徑 ) Tx I/Q Signal Company confdentaa...
  • Page 48 RF-2:GSM Trouble shooting (2/3) RF-2:GSM Trouble shooting (2/3) GSM 發射路徑 GSM transmission path • – 由於 2G PA 和 ASM 整合在 U1302, 檢查發射時對應邏輯控制電壓是否正確 – Due to 2G PA and ASM assembly in U1302, check logical control voltage is correct when transmission testing –...
  • Page 49 RF-2:GSM Trouble shooting (3/3) RF-2:GSM Trouble shooting (3/3) GSM 發射路徑 GSM transmission path • 檢查發射路徑的功率 – – check power of transmission path 使用 spectrum probe 量測下列標駐點 , 測量其功率 – – Use spectrum probe to measure below points’ power High band GSM signal Low band GSM signal...
  • Page 50 RF-3:WCDMA Trouble shooting (1/5) RF-3:WCDMA Trouble shooting (1/5) WCDMA 發射路徑 WCDMA transmission path • – 確認 IQ 路徑 – Check IQ path 使用示波器量測下圖所標之腳位 , 檢視其波形 – – Use oscilloscope to check below points, check waveform. Company confdentaa...
  • Page 51 RF-3:WCDMA Trouble shooting (2/5) RF-3:WCDMA Trouble shooting (2/5) WCDMA 發射路徑 WCDMA transmission path • 確認發射路徑 – – Check signal transmission path 使用频谱仪量測下圖所標之腳位 , 檢視其 Power – – Use oscilloscope to test below point and power Company confdentaa...
  • Page 52 RF-3:WCDMA Trouble shooting (3/5) RF-3:WCDMA Trouble shooting (3/5) WCDMA 發射路徑 WCDMA transmission path • Transceiver-3G PA, PA-Duplexer From MT6166 From MT6166 WCDMA BAND 1/2 signal WCDMA BAND 1/2 signal Company confdentaa...
  • Page 53 RF-3:WCDMA Trouble shooting (4/5) RF-3:WCDMA Trouble shooting (4/5) WCDMA 發射路徑 WCDMA transmission path – 檢查 ASM 邏輯控制電壓 – Check ASM logical control voltage – 使用示波器量測下圖所標腳位的電壓 , 是否符合右下列表 – Use oscilloscope test below pins voltage if they match the right bottom table Company confdentaa...
  • Page 54 RF-3:WCDMA Trouble shooting (5/5) RF-3:WCDMA Trouble shooting (5/5) 發射路徑 ASM-RF Con (GSM + WCDMA) • • Transmission Path ASM-RF Con (GSM + WCDMA) GSM PA+ASM Company confdentaa...
  • Page 55 RF-4:GSM/WCDMA Trouble shooting RF-4:GSM/WCDMA Trouble shooting 接收路徑 Receiving Path • 檢查 Antenna switch Module 邏輯控制電壓 – – Check Antenna switch module logical control voltage 使用示波器量測下圖所標腳位的電壓是否符合右下列表 – – Use oscilloscope test below pins voltage if they match the right bottom table Company confdentaa...
  • Page 56 WIFI /BT/GPS WIFI /BT/GPS WIFI/BT/GPS IC: MTK MT6627 BT/WIFI: 1. Check whether the antenna of BT\WIFI damaged 2. Check whether BT\WIFI R1503 has output frequency of 26M （ co _ clock design ） 3. Check BT\WIFI TRX path Company confdentaa...
  • Page 57 WIFI /BT/GPS WIFI /BT/GPS BT/WIFI TRX path ： Co_clock design ： MT6166 U1303 MT6627 U1504 MT6627 U1504 Company confdentaa...
  • Page 58 WIFI /BT/GPS WIFI /BT/GPS GPS RX path ： 1. Check whether the antenna of GPS damaged 2. Check whether the working voltage is normal Vcc:2.8V;GPS_LNA_EN:1.8V 3. Check whether the GPS signal has been enlarged Company confdentaa...
  • Page 59 WIFI /BT/GPS WIFI /BT/GPS GPS RX path U1506 MT6627 U1504 Company confdentaa...
  • Page 60 Thank You ！ Company confdentaa...