SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ...................... A1-1 HOW TO ORDER PARTS ........................... A1-1 IMPORTANT ..............................A1-1 CONTENTS ..............................A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-5 DISASSEMBLY INSTRUCTIONS 1.REMOVAL OF ANODE CAP ......................B1-1 2.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............... B2-1, B2-2 SERVICE MODE LIST ..........................
GENERAL SPECIFICATIONS CRT Size / Visual Size 15 inch / 357mmV System CRT Type Flat Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System Speaker 1 Speaker Position Front Size 1.5 x2.7 Inch Impedance Sound Output 10%(Typical) DDR SECAM NTSC3.58(AV)+NTSC4.43 PAL60Hz Tuning Broadcasting System CCIR...
Page 5
GENERAL SPECIFICATIONS On Screen Menu Display Menu Type Character Picture Contrast Brightness Colour Tint (NTSC Only) Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off CH Tuning Manual CH MAPPING CH Allocation Text Langage(East/West) Language Clock Set On/OffTimer Set On Timer Set Pin Code Registration Panel Lock...
Page 6
GENERAL SPECIFICATIONS G-10 Remote Unit RC-GX Control Glow in Dark Remocon Format Custom Code 40-BF h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys 34 Keys Keys Power 1/Rename 2/Move Volume Up / + Volume Down / - Previous Select Picture Menu...
Page 7
Wss Signal Wide Change Virtual Dolby Surround Hotel Lock G-12 Accessories Owner's Manual Language Germany,Dutch,Italian w/Guarantee Card Buyer Model No. 15V31D x Remote Control Unit Rod Antenna Poles 2Pole Terminal D-type Loop Antenna Terminal U/V Mixer DC Car Cord (Center+)
Page 8
W x D x H(mm) x 472 x 457 Design As per Buyer's Description of Origin No (Assembled in UK) Buyer Model No. 15V31D Natural Dropping At 1 Corner / 3 Edges / 6 Drop Test Surfaces Height (cm) Container Stuffing Sets/40' container...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 11
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 2-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 2 seconds. Remocon Key Operations Set Key Reset the user setting items (PICTURE, VOLUME and LANGUAGE) to the initial state VOL.
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE 2. BASIC ADJUSTMENTS Read and perform these adjustments when repairing the 2-1: CONSTANT VOLTAGE circuits or replacing electrical parts or PCB assemblies. Place the set with Aging Test for more than 5 minutes. CAUTION Connect the digital voltmeter to TP501. Set condition is AV MODE without signal.
Page 14
ELECTRICAL ADJUSTMENTS 2-6: FOCUS 2-10: BRIGHT CENT Receive a 70dB monoscope pattern. Receive the PAL black pattern*. (RF Input) Turn the Focus Volume fully counterclockwise once. Using the remote control, set the brightness and Adjust the Focus Volume until picture is distinct. contrast to normal position.
Page 15
ELECTRICAL ADJUSTMENTS 2-13: TINT Receive the NTSC color bar pattern. (Audio Video Input) Using the remote control, set the brightness and contrast to normal position. Connect the oscilloscope to TP024. Activate the adjustment mode display of Fig. 1-1 and press the channel button (20) on the remote control to select "TINT".
Page 16
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
BLOCK DIAGRAM CH UP TU001 MICON W/T.TEXT IC CH DOWN IC101 OECF013B Q102 SCL SDA VOL UP LED DRIVE ON_TIMER Q103 KEY_IN VOL DOWN LED DRIVE STANDBY LED ON TIMER P.CON+5V D103 STAND BY/P.ON MEMORY IC SDA 19 CHROMA IC D101 AVDD1 IC199...
Page 19
MICON/TUNER SCHEMATIC DIAGRAM (MAIN PCB) TU001 TUWRF4EG-778F2A ACCESSORY OS101 LED DRIVE ON TIMER RPM7138-H5 Q102 D103 UM-4 2SA1037AK R137 BT001 R104 R103 R102 R101 TM101 LTL-1CHGE-002A 2.2K 1.2K LED DRIVE R03(AB)2PXGPI RC-GX010 STAND BY/P.ON GREEN ANT001 Q103 D101 CP001 2SA1037AK R132 T4-216AP-BK 003P-2100...
WAVEFORMS MICON/TUNER IF/CHROMA 0.5µs 50µs 20µs 100mV 0.5V 10ms 50µs 100mV 200mV 20µs 20µs 50µs 0.5V 0.2ms 20µs 20µs 50µs 0.2ms 20µs 100mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS 20µs 20µs 20µs 100mV 20µs 20µs 200mV 20µs 10ms 100mV 200mV DEFLECTION/CRT 20µs 20µs 10ms 200mV 21PIN/AV SW 10ms 20µs 20µs NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 27
WAVEFORMS 10ms 20µs 20µs 20µs SOUND AMP 20µs 0.5V 2µs 0.2ms 200V 20µs NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.