CONTENT CONTENT ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐2 Technical Specification‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐3‐14 Block Diagram ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐15 List of key parts‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐16 IC BLOCK Diagram‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐17‐49 Factory Adjust Menu ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐50‐54 MAIN PCB‐TOP‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐55 ...
Technical Specification 1. Application Area: This product standard is use for LED 5M67B chassis. 2. Specification: All the standard are measured under following conditions without other specification. 2.1 Ambient Temperature: 20+/‐5℃ 2.2 Relative Humidity: 65+‐10% 2.3 Power Supply Voltage: Standard Input Voltage(100~240V AC 50/60HZ) 2.4 Adjust after 20 minutes warm‐up. ...
Page 4
Technical Specification 4. Safety and Regulation NO. Item Typ Max Unit Remark 1. Force Stability‐Incline plane Tip Test 10 deg 2. Force Stability‐Level Tip Test 100 ...
Page 6
Technical Specification 9. External Interface NO. Item Typ Max Unit Remark 1. Video Input Level 1 Vpp 75 ohm 2. Video Input Frequency Response 4.5 MHz ...
Page 7
Technical Specification 11. Customer Menu Setup(as shipped condition) NO. Item Specification Remark 1. PSM Standard 2. SSM Standard 3. Volume 30 4. Mute ...
Page 8
Technical Specification DTV‐Productions Specification Model # 29”/32”/39” Production content ID for reference only Country(WestEu./EastEu./Russia/AP/US/S.A./Jap Brazil an/…) Brand name Category (Monitor/TV/Combo/Portable TV…) TV TV Type(ATV、DTV(DVB‐T/DVB‐T2/DTMB/ATSC/ ISDB‐T (SBTVD‐T) ISDB‐T…)) Panel technology (LCD / LED/PDP) LED Market Position (High/Mid/Access,,,) Access ...
Page 9
Technical Specification Colour Temp@ maximum brightness Horizontal and vertical viewing angle Contrast ratio Typical panel Life Time (Hours) second panel supplier : panel reference Skyworth‐RGB Panel Display Type(MVA/PVA/IPS/…) TBD 1st panel supplier : resolution TBD Dynamic contrast ratio 1000 ...
Page 10
Technical Specification Special sound effect ( AVL / WIDE / Pseudo AVL /… ) Suround system ( Dolby / VD / SRS / BBE / … ) Surround Sound control ( Volume , Balance , Mute ) Volume,Balance,Mute Standard / Music / Film / News / Sound presets (User/Speech/News/Standard) Personal Headphone volume control ( Separated / Linked linked ) Sound quality ( High / Mid / Low ) Mid Reception and Decoding capability RF range(ATV) 54MHz‐864MHz 54MHz‐864MHz RF range(DTV) ...
Page 11
Technical Specification Terra No Twitter No Picasa No WiFi No User convenience OSD Language* English,Portuguese,Spanish OSD Positioning High‐class OSD Transparency Adjust No OSD Timeout Adjust No Customer Brand name(LOGO) Yes IB languages English,Portuguese ...
Page 12
Technical Specification programms) Calendar / Games No No program auto switch off Yes Hotel mode (Y/N) Yes DVD/BD module player (No/slot/tray) No Tuner FM (yes/No) No software USB download(RS232/CI/USB/OAD/NET) Factory reset Yes Screen saver No Blue Back ...
Page 13
Technical Specification Component Audio Input (YCrCb/YPrPb) 0 Headphone output connector (dia.mm) 1 (Shared with fixed audio out) CINCH subwoofer out / Coaxial out No (S/PDIF) USB slot (No/1.1/2/3/4) 2 DVB‐CI (common interface,CI+) No DLNA No UI/RC UI design spec. Skyworth UI design (font/pixel, 2D/3D graphic 2D engine..) RC Model TBD ...
Page 14
Technical Specification ref/No) ‐ Panel Tilt (Fowards/Backwards/Rotation) Swivel function desktop stand (yes/No) + motorized? Docking station (yes/No) Floor Stand (included/optionnal + ref/No) Glass shield (yes/No) Finish on Front Finish on side Finish on back Finish on stand number of colors on carton box ...
5M67B Factory Adjust Menu (V0.0) 1. Description Enter factory mode: Open source menu, and then press digital button “3”,”1”,”9”,”5” in turns to enter the factory menu. Press ↑ and ↓ button to choose the item, press OK button enter the submenu, press MENU to ruturn to upper menu, press ← and → button to adjust the value. Leave factory mode: ...
Page 51
VGA source ADC: Switch to PC source, input tessellated white and black signal, enter factory menu, select “AUTO ADC”item in the “ADC ADJUST” menu, press → button to begin auto adjust. When it is finish, it will show ”SUCCESS” or “FAILE”. If “FAILE” is shower, you need to try again. White balance: ...
Page 52
(2) Connect the debug tool to the device, turn on TV. Press “Connect” button. (3) Press “Read” button to choose the MBoot file. ‐52‐ ...
Page 53
(4) Press “Auto” button, set parameter. (5) Press “Run” button to begin program. (6) If program success, it will show “Pass” message, otherwise, you need to reconnect and try again. ‐53‐ ...
Page 54
Update main software(by USB): Copy the new software (named by “MstarUpgrade.bin”) to the root directory of USB drive. Press the button “MENU” , then enter “SETUP” submenu, select “Software Update(USB)” item, press ← to begin the software update. (If the “Power On Mode” is “Secondary”, please enter “power” button to begin it. )Then the green light and red light flash alternatively until the update is over, then TV set will restart when it is finish. Note: You need to restart the TV set again by AC power. We suggest you need to do “INIT EEPROM” and “OutFactory Reset” after software updat. ‐54‐ ...
No audio & No backlight Led indicator “red” on Check the 5VSTB on “FB5” Press the “ON/OFF” on keyboard & remote control, led turns green Check the AC input on Upgrade the software power supply board Upgrade the Check the 5V, & 12V on software the mainboard Done...
Page 75
Has video but no audio Check the Volume has set to “0” or it is mute Check the audio input line Done & the audio input circuit. Check the voltage of “Mute” pin beside Done the amplifier IC. It should not be 0V. = 0V Check the mute circuit >...
Page 76
Has audio but no video Check if the backlight is on Check the connector of Check the LVDS line backlight cable connected if it is connected Safely connect the Safely connect the Make sure the LVDS power is correct Check the backlight cable LVDS line (12V for 29”,32”&39”)
Page 77
Has backlight but no video Make sure the LVDS power is correct (12V for 29”,32”&39”) Correct the Upgrade the right S/W power Done Check the power supply of U100 Done Change a panel Fix the power supply Done Done Change the main IC U100 Done Change the...
Page 78
OSD Error Do EEPROM reset Upgrade the main S/W & do EEPROM reset Feed back to Skyworth Done...
Page 79
HD Mode, has flickering anomalistic bright line Make sure the power supply of main processor “U100” & DDRAM “U102” is correct Correct the power Change the “U102” supply Done Feed back to Skyworth...