Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Electrical shock
instructions
hazard
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
‰
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets
and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. You
must also read and understand the following instructions concerning electrical safety.
1.1.1.
Ensure that cables are always protected against short circuit and overload.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections
to ensure that none are loose.
IMPORTANT: Ensure that the voltage marked on the appliance matches the power supply to be
1.1.3.
used and that the plug is fitted with the correct fuse - see fuse rating at right.
DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired or
1.1.4.
replaced immediately by a competent electrician.
1.1.5.
It is recommended that this heater is wired directly to a fused isolator switch. If, however, a plug
is fitted, the following applies:
1.1.6.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable restraint is tight.
1.2.
GENERAL SAFETY
WARNING! Ensure the heater is at least 1m from any object, 500mm from the ceiling and 1800mm from floor level.
‰
WARNING! This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when
‰
they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating.
‰
WARNING! Never touch the element directly with fingers. Use a soft cloth, otherwise the tube may get damaged.
‰
WARNING! In order to avoid overheating, do not cover the heater.
‰
Familiarise yourself with the applications and limitations of the heater.
9
Ensure the heater is in good condition before use. If in any doubt do not use the unit and contact your Sealey stockist.
9
Only use recommended attachments and parts. Using unauthorised parts may be dangerous and will invalidate your warranty.
9
Check that element guards are in place, undamaged and firmly attached.
9
Keep tools and other items away from the heater when it is in use.
9
Keep the work area clean and clear of unnecessary items.
9
Keep children and unauthorised persons away from the heater, as it gets very hot.
9
Disconnect from mains and allow to cool before moving or attempting any cleaning or maintenance.
9
DO NOT USE WITH AN EXTENSION CABLE.
8
DO NOT use this heater with timers or other devices which switch the heater on automatically.
8
DO NOT immerse the heater in water.
8
DO NOT locate the heater below the power outlet.
8
DO NOT move the heater whilst in operation or even when still warm.
8
DO NOT use the heater to perform a task for which it has not been designed.
8
DO NOT use this heater with a programmer, timer, separate remote-control system or any other device that switches the heater on
8
automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
DO NOT use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
8
NOTE: Two dark points may exist on the surface of the heating element, or the surface of the heating element may turn white during the first
few minutes of operation. This is normal and will not affect the performance of the heater.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and
vulnerable people are present.
NOTE:
Children of less than 3 years should be kept away unless supervised continuously.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed
in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
© Jack Sealey Limited
2000W HIGH EFFICIENCY INFRARED SHORT
WAVE WALL MOUNTING HEATER
MODEL NO:
DO NOT cover
Hot surfaces
Original Language Version
IWMH2000R.V2
Recommended fuse rating
13 Amp
IWMH2000R.V2 Issue 3 (3,4) 11/06/2021
Advertisement
Related Manuals for Sealey IWMH2000R.V2
Summary of Contents for Sealey IWMH2000R.V2
- Page 1 Familiarise yourself with the applications and limitations of the heater. Ensure the heater is in good condition before use. If in any doubt do not use the unit and contact your Sealey stockist. Only use recommended attachments and parts. Using unauthorised parts may be dangerous and will invalidate your warranty.
- Page 2 The heater must be installed no less than 400 mm form side walls and no less than 1800 mm off the floor. WARNING! Ensure that the supply cable is well mounted and that it does not ‰ come into contact with reflector of the heater or that it does not trail into heated area, the supply cable can be fixed to the metal mounting bracket behind heater with plastic zip ties. The heater must be installed at least 1.8m above the floor. fig.4 IWMH2000R.V2 Issue 3 (3,4) 11/06/2021 Original Language Version © Jack Sealey Limited...
- Page 3 If heater will not turn on. Check the cable is plugged into an electrical outlet, if not, plug in. 7.2. Check if electricity to the building is working. 7.3. Bulb is lit, but no heat: Bulb is damaged. Arrange for replacement bulb with your Sealey stockist. Original Language Version IWMH2000R.V2 Issue 3 (3,4) 11/06/2021 © Jack Sealey Limited...
- Page 4 BATTERY REMOVAL: REMOTE CONTROL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.