Fujitsu AIRSTAGE AUXB004GLEH Installation Manual
Ndoor unit (cassette type)
Hide thumbs
Also See for AIRSTAGE AUXB004GLEH:
- Operating manual (6 pages) ,
- Design & technical manual (1038 pages) ,
- Design & technical manual (1092 pages)
Table of Contents
Advertisement
AUXB004GLEH
AUXB007GLEH
AUXB009GLEH
AUXB012GLEH
AUXB014GLEH
AUXB018GLEH
AUXB024GLEH
Refer to the rating label for the serial number,
manufactured year and month.
TM
INSTALLATION MANUAL
INSTALLATIONSANLEITUNG
MANUEL D'INSTALLATION
MANUAL DE INSTALACIÓN
Únicamente para personal de servicio autorizado.
MANUALE DI INSTALLAZIONE
A uso esclusivo del personale tecnico autorizzato.
ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ
ΕΣΩΤΕΡΙΚΗ ΜΟΝΑΔΑ (Τύπος Κασέτας)
Μόνο για εξουσιοδοτημένο τεχνικό προσωπικό.
MANUAL DE INSTALAÇÃO
РУКОВОДСТВО ПО УСТАНОВКЕ
ВНУТРЕННИЙ МОДУЛЬ (кассетного типа)
Только для авторизованного обслуживающего персонала.
INDOOR UNIT (Cassette Type)
For authorized service personnel only.
INNENGERÄT (Kassettentyp)
Nur für autorisiertes Fachpersonal.
UNITÉ INTÉRIEURE (type cassette)
Pour le personnel agréé uniquement.
UNIDAD INTERIOR (Tipo casete)
UNITÀ INTERNA (tipo a cassetta)
UNIDADE INTERIOR (Tipo Cassete)
Apenas para técnicos autorizados.
MONTAJ KILAVUZU
İÇ ÜNİTE (Kaset Tipi)
Yalnızca yetkili servis personeli için.
[Original instructions]
PART No. 9371022635
MADE IN P.R.C.
Advertisement
Table of Contents
Related Manuals for Fujitsu AIRSTAGE AUXB004GLEH
Summary of Contents for Fujitsu AIRSTAGE AUXB004GLEH
- Page 1 INSTALLATION MANUAL INDOOR UNIT (Cassette Type) For authorized service personnel only. INSTALLATIONSANLEITUNG INNENGERÄT (Kassettentyp) Nur für autorisiertes Fachpersonal. MANUEL D’INSTALLATION UNITÉ INTÉRIEURE (type cassette) AUXB004GLEH Pour le personnel agréé uniquement. AUXB007GLEH MANUAL DE INSTALACIÓN AUXB009GLEH AUXB012GLEH UNIDAD INTERIOR (Tipo casete) AUXB014GLEH Únicamente para personal de servicio autorizado.
-
Page 2: Table Of Contents
INSTALLATION MANUAL This mark indicates procedures which, if improperly performed, CAUTION might possibly result in personal harm to the user, or damage PART No. 9371022635 to property. VRF system indoor unit (Cassette type) Read carefully all security information before use or install the air conditioner. Contents Do not attempt to install the air conditioner or a part of the air conditioner by yourself. -
Page 3: Optional Parts
Do not discard any accessories needed for installation until the installation work has been Description Model Application completed. Fresh air intake kit UTZ-VXAA To take fresh air. Name and Shape Q’ty Application Wireless LAN adapter UTY-TFSXZ* For wireless LAN control. Operating manual Supply power to the indoor unit PCB when External power supply... -
Page 4: Discharge Direction Setting
H: Maximum height from floor to ceiling Fig. D Drain pipe (O.D. ø25.4) Unit: mm H (mm) Model name AUXB004 AUXB007 AUXB009 AUXB012 AUXB014 AUXB018 AUXB024 Standard mode 2,700 2,700 2,700 2,700 2,700 2,700 2,700 High Ceiling 3,000 3,000 3,000 3,000 mode * Be sure to make the function settings with the remote controller according to the... -
Page 5: Pipe Requirement
4.3.3. Pipe connection 4.2. Pipe requirement When the flare nut is tightened properly by Tighten with 2 your hand, hold the body side coupling with CAUTION wrenches. a separate spanner, then tighten with a torque wrench. (See the table below for the Holding Refer to the installation manual for the outdoor unit for description of allowable pipe flare nut tightening torques.) -
Page 6: Electrical Wiring
When lifting up drain: NOTE: Check for drainage Drain pipe • Height of inclined pipe should be less than 700 mm from the ceiling. A rise dimension Pour about 1 liter of water over this range will cause leakage. from the position shown in the •... -
Page 7: Wiring Method
Breaker should be installed at every refrigerant system. Do not use a breaker in a different 6.3. Unit wiring refrigerant system. Refer to the table for the breaker specifications of each installation condition. Perform the power crossover wiring within the range of the same refrigerant system. When the Before attaching the cable to terminal block. -
Page 8: Connection Of Wiring
6.3.2. Transmission and Remote controller cable (2) Connect the connection cable, with the cable tie. Transmission cable Remote controller cable Y1,Y2: Remote 30 mm 30 mm controller cable Shield cable Cable tie (Medium) (no film) (Accessories) 40 mm X1, X2: •... -
Page 9: External Input And External Output (Optional Parts)
6.5.3. Connection methods DC power supply Wire modification for External IMPORTANT: P.C.B 12 to 24V input/output wire Be sure to insulate the connection between the Load resis- (1) Remove insulation from wire at- tance wires. CNA01 tached to wire kit connector. Locally Wire kit connector (2) Remove insulation from field... -
Page 10: Field Setting
● When function setting is “Emergency stop” mode. Operation behavior [In the case of “Edge” input] Connector Output voltage Status Connector Input signal Command Stop External output1 OFF → ON Emergency stop Pins 1-2 DC 12 V Operation Ch1 of CNA01 or CNA02 ON →... -
Page 11: Custom Code Setting
Function 7.2. Custom code setting Function Setting number Default Details number • Selecting the custom code prevents the indoor unit mix-up. (figure below) (Up to 4 codes Allow an external controller to start 00 Start/Stop can be set.) or stop the system, or to perform an Emergency •... -
Page 12: Cassette Grille Installation
7.3.2. Checking the function settings (2) Open the intake grille and remove. Press and hold the “MANUAL AUTO” button on the indoor unit for 3 seconds to check the function settings. It is necessary to disconnect the power in order to return to normal operation mode. -
Page 13: Attach The Intake Grille
8.3. Attach the intake grille 11. ERROR CODES The installation is the reverse of “REMOVING THE INTAKE GRILLE”. If you use a wired type remote controller, error codes will appear on the remote controller The intake grille can be rotated and installed 4 ways to suit the user’s preference. display.