hit counter code
Sony mex-1gp Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Car Receiver
  5. MEX 1GP - Giga Panel Radio
  6. Service manual

Sony mex-1gp Service Manual

Hide thumbs Also See for mex-1gp:
Table of Contents

Advertisement

Quick Links

See also: Operating Instructions , Read This First
SERVICE MANUAL
Ver. 1.0 2006.02
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS (US MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
GIGA PANEL section
Signal-to-noise ratio
120 dB
Frequency response
10 – 20,000 Hz
Tuner section
FM
Tuning range
US, Canadian model: 87.5 – 107.9 MHz
AEP, UK, E model: 87.5 – 108 MHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM (US, Canadian model)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
30 µV
Sony Corporation
9-887-045-01
eVehicle Division
2006B04-1
Published b y Sony Techno Create Corporation
© 2006.02
MEX-1GP
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
MW/LW (AEP, UK, E model)
Tuning range
Antenna terminal
Intermediate frequency
Sensitivity
Power amplifier section
Outputs
Speaker impedance
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Inputs
Tone controls
NETWORK AUDIO SYSTEM
US Model
Canadian Model
AEP Model
UK Model
E Model
CDX-GT30W/GT300/GT300EE/
GT300S/GT350/GT350S
MG-611WA-186//Q
KSS1000E
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
External antenna connector
10.7 MHz/450 kHz
MW: 30 µV
LW: 40 µV
Speaker outputs (sure seal connectors)
4 – 8 ohms
Audio outputs terminal
(front, sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input/AUX IN terminal
Remote controller input terminal
Antenna input terminal
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
– Continued on next page –

Advertisement

Table of Contents
loading

Related Manuals for Sony mex-1gp

Summary of Contents for Sony mex-1gp

  • Page 1 Mid: ±10 dB at 1 kHz (XPLOD) Intermediate frequency 10.7 MHz/450 kHz High: ±10 dB at 10 kHz (XPLOD) Sensitivity 30 µV – Continued on next page – NETWORK AUDIO SYSTEM Sony Corporation 9-887-045-01 eVehicle Division 2006B04-1 Published b y Sony Techno Create Corporation © 2006.02...
  • Page 2 THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REPLACE THESE COMPONENTS WITH SONY PARTS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3 MEX-1GP • CD Playback: You can play CD-DA (also containing CD TEXT* ), CD-R/CD- RW (MP3/WMA files also containing Multi Session and ATRAC CD (ATRAC3 and ATRAC3plus format). Type of discs Label on the disc CD-DA ATRAC CD *1 A CD TEXT disc is a CD-DA that includes information such as disc, artist and track name.

  • Page 4: Table Of Contents

    MEX-1GP • UNLEADED SOLDER TABLE OF CONTENTS Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. GENERAL (Caution: Some printed circuit boards may not come printed with Location of Controls ............5 the lead free mark due to their particular size.)

  • Page 5: General

    MEX-1GP SECTION 1 This section is extracted GENERAL from instruction manual. • LOCATION OF CONTROLS • US, Canadian Model Location of controls and basic operations Main unit H GP* T Disc slot 5 /ALBM* +/– buttons* To skip groups/albums (press); skip groups/ To insert the disc.
  • Page 6 MEX-1GP • US, Canadian Model Source selector (not supplied) Sélecteur de source Supplied with the CD/MD changer (non fourni) Fourni avec le changeur de CD/MD Selector de fuente Suministrado con el cambiador de CD/MD (no suministrado) Supplied with XA-C40 XA-C40...

  • Page 7: Connection Example

    MEX-1GP • LOCATION OF CONTROLS • AEP, UK Model Location of controls and basic operations Main unit G OPEN button 5 S Z (eject) button 5 To eject the disc. H GP* /ALBM* +/– buttons* T Disc slot 5 To skip groups/albums (press); skip groups/ albums continuously (press and hold).

  • Page 8: Connection Diagram

    MEX-1GP • AEP, UK Model Auxiliary equipment such as portable Note for the aerial connecting Hinweis zum Anschließen der Antenne Remarque sur le raccordement de Nota per il collegamento dell’antenna Opmerking bij de antenne-aansluiting If your car aerial is an ISO (International Wenn Ihre Fahrzeugantenne der l’antenne...
  • Page 9 MEX-1GP • LOCATION OF CONTROLS • E Model Location of controls and basic operations Main unit G OPEN button 5 S Z (eject) button 5 To eject the disc. H GP* /ALBM* +/– buttons* T Disc slot 5 To skip groups/albums (press); skip groups/ albums continuously (press and hold).
  • Page 10 MEX-1GP • E Model...

  • Page 11: Disassembly

    MEX-1GP SECTION 2 DISASSEMBLY Note: This set can be disassemble according to the following sequence. 2-1. SUB PANEL ASSY (Page 12) 2-2. CD MECHANISM BLOCK (Page 12) 2-10. SERVO BOARD 2-4. CHASSIS (T) SUB ASSY 2-3. MAIN BOARD (Page 16)

  • Page 12: Sub Panel Assy

    MEX-1GP Note: Follow the disassembly procedure in the numerical order given. 2-1. SUB PANEL ASSY 3 two claws 2 two claws 4 flexible flat cable (22 core) 1 two screws (CN602) (+PTT 2.6 × 6) 5 sub panel assy 2-2. CD MECHANISM BLOCK...

  • Page 13: Main Board

    MEX-1GP 2-3. MAIN BOARD 2 two screws (+PTT 2.6 × 8) 1 three screws (+BTT 2.6 × 5) 3 MAIN board 4 insulating sheet 2-4. CHASSIS (T) SUB ASSY 4 claw 2 two screws (+P 1.7 × 2.2) 1 two screws (+P 1.7 ×...

  • Page 14: Roller Arm Assy

    MEX-1GP 2-5. ROLLER ARM ASSY 3 washer 5 roller arm assy 4 gear (RA1) 2 spring (RAR-B) 1 spring (RAL-B) 2-6. CHASSIS (OP) ASSSY qa chassis (OP) assy 0 coil spring (damper) lever (D) 4 washer 1 optical pick-up (16 core)

  • Page 15: Optical Pick-Up

    MEX-1GP 2-7. OPTICAL PICK-UP 2 chucking arm sub assy 5 claw 1 tension coil spring (CHKG) 7 optical pick-up 6 main shaft 4 rack (SL) 3 screw (+B 1.4 × 5) 2-8. SL MOTOR ASSY (M902) 1 screw (+P 1.4 × 1.8)

  • Page 16: Le Motor Assy (M903)

    MEX-1GP 2-9. LE MOTOR ASSY (M903) 8 screw 0 gear (LE) assy (+M 1.7 × 2.5) 9 bearing (LEB-N) 2 washer qa screw (+M 1.7 × 2.5) qf two toothed lock screws 3 gear (LE1) (+M 1.4 ) lever (D)

  • Page 17: Diagrams

    MEX-1GP SECTION 3 DIAGRAMS 3-1. BLOCK DIAGRAM — CD SECTION — • R-ch is omitted due to same as L-ch. • Signal Path : CD PLAY DETECTOR MAIN FPI2 AGCI RFEQO CD-L SECTION RFRPI (Page 19) R-CH FNI2 FPI1 FNI1...

  • Page 18: Block Diagram -Memory Section

    MEX-1GP 3-2. BLOCK DIAGRAM — MEMORY SECTION — USB I/F IC902 BUS SWITCH CODEC D/A CONVERTER IC906 IC915 IC911 IC908 CN901 DPRS D1 – 8 D1 – 8 MAIN DIO0 DA_0 DAC_DATA 103 2 DATA OUTL 7 AUDIO_L SECTION C_BCK 105...

  • Page 19: Block Diagram -Main Section

    MEX-1GP 3-3. BLOCK DIAGRAM — MAIN SECTION — Q301 ELECTRONIC VOLUME AUDIO IN IC401 (Page 18) R-CH MEMORY AUDIO_L 11 DIFEL SECTION R-CH 13 DIFFR PJ401 REAR R-CH R-CH AUDIO CD-L 9 SE1L SECTION OUTLF R-CH 10 SE1R (Page 17)

  • Page 20: Block Diagram -Key Section

    MEX-1GP 3-4. BLOCK DIAGRAM — KEY SECTION — SYSTEM CONTROL IC801 (4/4) CN601 FLASH_W FLASH WRITER DISPLAY CONTROL IC913 RE901 RE_0 ROTARY LCD901 VOL/ SEG9 ENCODER RE_1 PUSH SELECT LIQUID LCD_SO SEG62 CRYSTAL LCD_SCK DISPLAY COM1 LCD_CE PANEL KEY MATRIX...

  • Page 21: Circuit Boards Location

    MEX-1GP 3-5. CIRCUIT BOARDS LOCATION • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is SERVO board printed in each block.) SENSOR board For schematic diagrams.

  • Page 22: Printed Wiring Boards -Cd Mechanism Section

    MEX-1GP 3-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 21 for Circuit Boards Location. : Uses unleaded solder. TP39 TP38 TP26 TP24 TP41 FMB3 FMA6 TP23 TP29 TP42 TP43 TP45 TP27 TP44 TP37 TP46 TP53...

  • Page 23: Schematic Diagram -Cd Mechanism Section (1/2)

    MEX-1GP 3-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 21 for Waveforms. TP33 TP32 TP31 TP52 TP38 TP39 TP53 R132 C132 R133 TP41 C133 TP50 R29 R19 TP51 TP21 TP22 TP49 TP23 TP24 TP25 TP26...

  • Page 24: Schematic Diagram -Cd Mechanism Section (2/2)

    MEX-1GP • Refer to page 21 for Waveform. • Refer to page 33 for IC Block Diagram. 3-8. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 36 for IC Pin Descriptions. (Page 23) (Page 28) CN751...

  • Page 25: Printed Wiring Boards -Main Section

    MEX-1GP 3-9. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 21 for Circuit Boards Location. : Uses unleaded solder. PJ401 AUDIO OUT AUDIO IN REAR FRONT PJ601 (ANTENNA) CNP900 (REMOTE IN) –1 –2 –1 –2 –1 –2...

  • Page 26: Schematic Diagram -Main Section (1/3)

    MEX-1GP • Refer to page 21 for Waveforms. 3-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 33 for IC Block Diagrams. C433 C434 C436 PJ401 C435 R426 PJ601 C439 R425 R468 C605 C604 C443 R428 R430...

  • Page 27: Schematic Diagram -Main Section (2/3)

    MEX-1GP 3-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 35 for IC Block Diagrams. C113 C101 C107 D921 D922 IC B/D CNP901 IC100 C993 C991 R920 R913 F901 D914 (Page 26) C106 C994 C990 C109 C111...

  • Page 28: Schematic Diagram -Main Section (3/3)

    MEX-1GP • Refer to page 21 for Waveform. • Refer to page 35 for IC Block Diagram. 3-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 38 for IC Pin Descriptions. (Page 26) (Page 27) JC812 R866...

  • Page 29: Printed Wiring Board -Sub Section

    MEX-1GP 3-13. PRINTED WIRING BOARD — SUB SECTION — • Refer to page 22 for Circuit Boards Location. : Uses unleaded solder. D940 LED919 D941 CN501 R1023 LED920 S901 (DISC IN) LED919, S901 (11) KEY BOARD CN902 (Page 30) (Page 25)

  • Page 30: Printed Wiring Board -Key Section

    MEX-1GP 3-14. PRINTED WIRING BOARD — KEY SECTION — • Refer to page 21 for Circuit Boards Location. : Uses unleaded solder. LSW907 IC912 AEP,UK,E MODEL US,CND MODEL LED903,S910 BTM/CAT S912 LSW901 OPEN LSW901 C969 R961 R1017 IC912 R972 S910...

  • Page 31: Schematic Diagram -Key Section (1/2)

    MEX-1GP 3-15. SCHEMATIC DIAGRAM — KEY SECTION (1/2) — R953 R960 R974 R987 R993 R951 R957 R971 R984 R990 R995 R997 R998 R1008 LSW907(2/2) LSW908(2/2) LSW904(2/2) R1013 R1017 LED912 LED905 LED910 LED917 C969 C971 IC912 LED907 LED915 LED909 LED902 LED914...

  • Page 32: Schematic Diagram -Key Section (2/2)

    MEX-1GP IC907 in the key board is not supplied. The IC907 cannot be replaced. The complete key board • Refer to page 21 for Waveforms. should be replaced. 3-16. SCHEMATIC DIAGRAM — KEY SECTION (2/2) — • Refer to page 40 for IC Pin Descriptions.

  • Page 33: Ic Block Diagrams

    MEX-1GP • IC BLOCK DIAGRAMS IC1 BA5968FP-E2 (SERVO Board (2/2)) OPIN4+ LDCTL OUTR OUTF OPIN4– OPOUT1 OPOUT4 OPIN3+ OPIN3– OPOUT2 OPOUT3 POWVCC MUTE MUTE VOL– VOL+ VOL+ VOL2– VOL3– LEVEL LEVEL SHIFT SHIFT VOL2+ VOL3+ VO1– VOL4– LEVEL LEVEL SHIFT...
  • Page 34 MEX-1GP IC401 TDA7419TR (MAIN Board (1/3)) ACOUTR ACINR ACINL SUBWOOFER L.P.F ACOUTL BUSS OUTRR2 MIDDLE VREF SAOUT SPECTRUM ANALYZER SAIN SE3L SE3R TREBLE SOFTSTEP VOLUME SOFT MUTE LOUDNESS MUTE OUTLF OUTLR OUTRR OUTRF IN GAIN AUTO ZERO SUPPLY SE2L SE2R...
  • Page 35 MEX-1GP IC100 TDA8588AJ/N2/R1 (MAIN Board (2/3)) I2C BUS PGND3 SGND PROTECTION DIAGNOSTIC ACGND PGND2 STANDBY MUTE CHIP DETECT PGND1 DIAGNOSTIC TEMPERATURE DIAG PROTECTION ENABLE LOGIC SWITCH CRES SWITCH REG1(AU8V) REG3(SERVO) REG4(MECHA) REG5(DISP+B) REFERENCE VOLTAGE LOADDUMP BACK-UP REG2(U-COM) REGULATOR PROTECTION SWITCH...
  • Page 36 MEX-1GP • IC PIN DESCRIPTIONS • IC3 MB90486BPFV-G-177E1 (CD SYSTEM CONTROL) (SERVO BOARD (2/2)) Pin No. Pin Name Pin Description CDON_1500MV Servo 1.5 V power supply control signal output 2 to 5 — Not used. (Open) DRVON Motor drive mute signal output...
  • Page 37 Not used in this set. MECON Mechanism deck power supply control signal output CDON Servo power supply control signal output XUART Sony-Bus/MC-Bus change signal input H: Sony-Bus, L: MC-Bus ZMUTE Zero detection mute signal output MECON_CHK MECHA +6V power rising detection signal input CDON_CHK SERVO +3.3V power rising detection signal input...
  • Page 38 MEX-1GP • IC801 MB90488BPF-G-215E1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) Pin No. Pin Name Pin Description Audio mute signal output 2 to 4 — Not used (Open) BEEP Beep signal output VOL_ATT Electronic volume ATT control signal output ILL signal input 8 to 10 —...
  • Page 39 MEX-1GP Pin No. Pin Name Pin Description TU_ATTIN Tuner mute zero cross detect signal input DAVN RDS data input DIAG Power AMP status signal input — Not used (Open) UNI_SI Bus control data input UNI_SO Bus control data output UNI_SCK...
  • Page 40 MEX-1GP • IC902 PL-2518ALQ64 (USB I/F) (KEY BOARD (2/2)) Pin No. Pin Name Pin Description SM_RB SDRAM ready/busy signal input SM_ALE SDRAM address latch enable signal output SUSPEND Suspend indicator output (Not used (Open)) SM_CEL SDRAM command latch enable signal output...
  • Page 41 MEX-1GP Pin No. Pin Name Pin Description Connected resister to VCC DMRS Full speed D+ signal input/output DPRS Full speed D– signal input/output AVCC3 — Power supply (+3.3V) AGND — Ground AVCC3 — Power supply (+3.3V) — Ground VCC3 —...
  • Page 42 MEX-1GP • IC911 MC38C8001 (CODEC) (KEY BOARD (2/2)) Pin No. Pin Name Pin Description 1 to 8 DA_0 to 7 SDRAM data input/output 9 to 16 DA_15 to 8 — Not used (Open) SD_DQM — Not used (Open) SD_DQM SDRAM command latch enable signal output VDD_33 —...
  • Page 43 MEX-1GP Pin No. Pin Name Pin Description VDD_18 — Power supply (+1.8V) — Ground NEINT (0) MA-SL serial data input NEINT (1) MA-SL request signal input NEINT (2) — Not used (Open) NEINT (3) — Not used (Open) U_TXD —...

  • Page 44: Exploded Views

    MEX-1GP SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark. number in the exploded views are not supplied. Example : 0 are critical for safety.

  • Page 45: Front Panel Section

    MEX-1GP 4-2. FRONT PANEL SECTION RE901 not supplied LCD901 not supplied supplied supplied not supplied supplied supplied supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-264-712-01 SPRING (OPEN) A-1151-341-A KEY BOARD, COMPLETE (AEP,UK,E)

  • Page 46: Cd Mechanism Section (1)

    MEX-1GP 4-3. CD MECHANISM SECTION (1) (MG-611WA-186//Q) not supplied (SENSOR board) not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3372-444-C CHASSIS (T) SUB ASSY 3-259-033-01 DAMPER (S) 3-253-729-11 SPRING (LR), TENSION COIL...

  • Page 47: Cd Mechanism Section (2)

    MEX-1GP 4-4. CD MECHANISM SECTION (2) (MG-611WA-186//Q) (including M901) M902 not supplied not supplied supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1075-644-A CHASSIS (OP) COMPLETE ASSY A-3372-446-A LEVER (SL) SUB ASSY 3-316-938-91 SCREW (B1.4X5), TAPPING...

  • Page 48: Cd Mechanism Section (3)

    MEX-1GP 4-5. CD MECHANISM SECTION (3) (MG-611WA-186//Q) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-348-993-01 WASHER 2-186-696-02 BRACKET (LEM-N) 2-186-699-01 GEAR (RA1) 3-345-648-91 SCREW (M1.4), TOOTHED LOCK A-1075-641-C ARM ASSY, ROLLER A-1083-636-A GEAR (LE) ASSY...

  • Page 49: Cd Mechanism Section (4)

    MEX-1GP 4-6. CD MECHANISM SECTION (4) (MG-611WA-186//Q) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-186-700-01 GEAR (CHK1) 2-630-962-01 WASHER (SLIT) 3-344-223-01 WASHER 2-590-545-31 GEAR (LE2-M) 3-259-470-12 GEAR (LE1) A-1075-640-B CHASSIS (M) BLOCK ASSY 3-253-755-41 LEVER (D)

  • Page 50: Electrical Parts List

    MEX-1GP SECTION 5 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark. the parts list may be different from the they are seldom required for routine service.
  • Page 51 MEX-1GP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D907 6-501-170-01 DIODE UDZW-TE17-6.8B LCD901 1-805-940-11 DISPLAY PANEL, LIQUID CRYSTAL (AEP,UK,E) D908 6-501-170-01 DIODE UDZW-TE17-6.8B D911 6-501-170-01 DIODE UDZW-TE17-6.8B < LED > D912 6-501-170-01 DIODE UDZW-TE17-6.8B D913 6-501-170-01 DIODE UDZW-TE17-6.8B...
  • Page 52 MEX-1GP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R909 1-218-945-11 RES-CHIP 1/16W R976 1-216-819-11 METAL CHIP 1/10W R910 1-220-884-81 METAL CHIP 0.5% 1/16W R977 1-216-821-11 METAL CHIP 1/10W R911 1-220-884-81 METAL CHIP 0.5% 1/16W R978 1-216-823-11 METAL CHIP 1.5K...
  • Page 53 MEX-1GP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1041 1-218-977-11 RES-CHIP 100K 1/16W < CAPACITOR > R1042 1-218-990-81 SHORT CHIP R1043 1-218-990-81 SHORT CHIP C101 1-126-964-11 ELECT 10uF R1052 1-218-990-81 SHORT CHIP C106 1-126-965-11 ELECT...
  • Page 54 MEX-1GP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C604 1-107-826-11 CERAMIC CHIP 0.1uF C909 1-162-970-11 CERAMIC CHIP 0.01uF (US,CND) C915 1-162-970-11 CERAMIC CHIP 0.01uF C605 1-126-963-11 ELECT 4.7uF C919 1-162-970-11 CERAMIC CHIP 0.01uF (AEP,UK,E)
  • Page 55 MEX-1GP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D858 8-719-058-24 DIODE RB501V-40TE-17 1-216-864-11 SHORT CHIP D901 6-501-180-01 DIODE UDZW-TE17-18B 1-216-864-11 SHORT CHIP D902 8-719-053-18 DIODE 1SR154-400TE-25 D903 8-719-053-18 DIODE 1SR154-400TE-25 < COIL > D904...
  • Page 56 MEX-1GP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R413 1-216-833-11 METAL CHIP 1/10W R621 1-216-864-11 SHORT CHIP 0 (AEP,UK,E) R414 1-216-809-11 METAL CHIP 1/10W R622 1-216-864-11 SHORT CHIP 0 (AEP,UK,E) R415 1-216-809-11 METAL CHIP...
  • Page 57 MEX-1GP MAIN SENSOR SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R883 1-216-845-11 METAL CHIP 100K 1/10W 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN) R884 1-216-809-11 METAL CHIP 1/10W ************************************************************* R885 1-216-833-11 METAL CHIP 1/10W...
  • Page 58 MEX-1GP SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-125-837-11 CERAMIC CHIP 6.3V 1-218-947-11 RES-CHIP 1/16W C132 1-125-837-11 CERAMIC CHIP 6.3V 1-218-947-11 RES-CHIP 1/16W C133 1-125-837-11 CERAMIC CHIP 6.3V 1-218-941-81 RES-CHIP 1/16W 1-218-941-81 RES-CHIP 1/16W <...
  • Page 59 MEX-1GP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark SUB BOARD 2-681-152-31 MANUAL, INSTRUCTION (FORMAT) (EzRecover) (ENGLISH,SIMPLIFIED CHINESE) ********** 1-831-502-11 CABLE, FLEXIBLE FLAT (22 CORE) (CN904) X-2055-358-1 CASE ASSY (for FRONT PANEL) ************************************************************* < CONNECTOR >...
  • Page 60 MEX-1GP REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2006.02...

Table of Contents