Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toro 30823
Summary of Contents for Toro 30823
- Page 1 Form No. 3363-169 Rev B Debris Blower Groundsmaster ® 200/3280-D/3320 Series Traction Unit Model No. 30823—Serial No. 310000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or Maintenance............... 12 additional information, contact an Authorized Service Lubrication............12 Dealer or Toro Customer Service and have the model Adjusting the Blower Belt ........13 and serial numbers of your product ready. Write the Storage............... 14 numbers in the space provided. -
Page 3: Safety
• The maximum seating capacity is one person. Never ever needed or assistance is desired, contact an carry passengers. Authorized Toro Distributor. • Sit on the seat when starting the engine and operating • To reduce a potential fire hazard, keep the engine free the machine. -
Page 4: Safety And Instructional Decals
Toro replacement parts and within a few hours by a doctor familiar with this accessories to keep the machine all Toro. Never form of injury or gangrene may result. use “will-fit” replacement parts and accessories •... - Page 5 93-9083 1. Cutting/dismemberment hazard, fan—stay away from moving parts. 99-4487 1. Read the Operator's 3. Grease every 8 hours. Manual. 2. Grease 4. Grease every 100 hours. 93-6674 1. Crushing hazard, hand—read the instructions before servicing or performing maintenance. 105-0708 105-0698 1.
-
Page 6: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Stop Bolts (7/16 x 3 inches) Mount the arms to the attachment frame Locknut (7/16 inch) Washer Bolt (7/16 x 3-1/4 inches) Mount the castor wheels to the debris –... -
Page 7: Mounting The Arms To The Attachment Frame
Attachment Frame Kit, Toro Part No. 110–8540 before Procedure the Debris Blower Mounting Kit can be installed. The Attachment Frame Kit can be obtained from your Toro 1. Position the machine on a clean, level surface. Lower Distributor. any implement, stop the engine, apply the parking brake and remove the key from the ignition switch. -
Page 8: Mounting The Castor Wheels
Figure 3 3. Right arm 1. Attachment frame 2. Stop Figure 4 1. Tensioning cap 3. Spacers Mounting the Castor Wheels 2. Thrust washers No Parts Required Procedure The castor wheel assemblies are installed upside down Lowering the Stand on the debris blower for shipping 1. -
Page 9: Mounting The Debris Blower To The Traction Unit
2. Lower the stand. Install the pin through the upper set of holes in the stand and tube (Figure 5). Secure the pin. 3. Stand the blower up on the castor wheels and stand Installing the Drive Shaft (storage position). Parts needed for this procedure: Drive shaft Roll pin... -
Page 10: Grease The Blower
Product Overview Specifications Backward curved, cast aluminum fan. 12 blades per side, 21 in. (53 cm) outside diameter, 6-3/8 in. (16 cm) width, 34 lb. (16 kg) Fan housing 10 gauge steel face plates welded to 10 gauge wrapper. Increasing scroll from cutoff. -
Page 11: Operation
Operation 3. Engage the PTO while the engine is at LOW IDLE. 4. Increase the engine speed to High IDLE. Transporting the Blower 5. Practice blowing material. It is advisable to blow the same direction the wind is blowing to prevent 1. -
Page 12: Maintenance
Maintenance Lubrication Idler Arm Bearing The idler arm bearing (Figure 10) must be lubricated after every 8 hours of operation with a No. 2 Lithium-based grease. Figure 11 Lift Arm Pivots The (2) lift arm pivots (Figure 12) must be lubricated after every 8 hours of operation with a No. -
Page 13: Adjusting The Blower Belt
2. A new belt is properly tensioned when the idler spring body is extended to a length of 3-1/4 to 3-1/2 in. (83-89 mm) (Figure 15). Figure 15 1. Idler spring 2. 3-1/4 to 3-1/2 in. (83-89 3. When the belt stretches, adjust it as follows: •... -
Page 14: Storage
Storage 1. Lower the stand. Install the pin through the upper set of holes in the stand and tube (Figure 5). Secure the pin. 2. Stand the blower up on the castor wheels and stand. 3. Thoroughly clean the blower. The fan housing should be free of dirt, leaves, and debris. -
Page 15: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The fan quits turning. 1. Belt may be loose or broken. 1. Replace belt or adjust the tension of the belt. 2. Bearing pressed in the bearing mount 2. Replace the bearing, use #609 Loctite may be damaged. - Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.