Operating and installation instructions Electric grill To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr. 07 180 420...
Contents Warning and Safety instructions................ 4 Caring for the environment ................ 12 Guide to the appliance .................. 13 Grill ........................13 CS 1312...................... 13 CS 1322...................... 14 Indicators....................... 14 Accessories supplied .................... 15 Using for the first time .................. 16 Cleaning the CombiSet for the first time ...............
They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these instructions. Keep these instructions in a safe place and ensure that new users...
Page 5
Warning and Safety instructions Correct application This grill is designed for domestic use and for use in similar envir- onments. This grill is not intended for outdoor use. This grill is intended for domestic use only to cook food and keep it warm.
Page 6
Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from the grill un- less they are constantly supervised. Children 8 years and older may only use the grill unsupervised if they have been shown how to use it safely and recognise and under- stand the consequences of incorrect operation.
Page 7
Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and re- pairs must only be carried out by a Miele authorised technician. A damaged grill can be dangerous. Check it for visible signs of damage.
Page 8
Miele authorised service technician. Otherwise the guar- antee is invalidated. Miele can only guarantee the safety of the appliance when genu- ine original Miele replacement parts are used. Faulty components must only be replaced by Miele spare parts.
Page 9
Warning and Safety instructions Correct use The grill gets hot when in use and remains hot for some time after being switched off. Do not touch the appliance if there is a possibility that it could still be hot. ...
Page 10
Warning and Safety instructions When using an electrical appliance, e.g. a hand-held food blender, near the grill, ensure that the cable of the electrical appliance cannot come into contact with the hot grill. The insulation on the cable could become damaged.
They should be cleaned regularly and replaced in good time. See "Cleaning and Care". Accessories Only use genuine original Miele accessories with this appliance. Using spare parts or accessories from other manufacturers will inval- idate the guarantee, and Miele cannot accept liability.
/ recycling centre for electrical and electronic ap- pliances, or contact your dealer or Miele for advice. You are also respons- ible by law for deleting any personal data that may be stored on the appli- ance being disposed of. Please ensure...
Guide to the appliance Grill CS 1312 a Grilling rack f Symbols for grilling area b Front heating element g Indicators c Rear heating element Controls for grilling area d Lava rock container h Front e Drain tap i Back...
Guide to the appliance CS 1322 a Grill racks f Symbols for grilling area b Front heating element g Indicators c Rear heating element Controls for grilling area d Lava rock container h Front e Drain tap i Back Indicators j In-operation indicator...
Using for the first time Please stick the extra data plate for Switching on the CombiSet for the appliance supplied with this doc- the first time umentation in the space provided in The metal components have a protect- the "After sales service, data plate, ive coating which when heated for the guarantee"...
Page 18
Grilling chart [min] Food Apple slices 2–3 Miscellaneous Toast 2–3 Tofu 4–6 Grilling duration Durations quoted in the chart are for guidance only and apply to food grilled using settings between 9–11 on a pre-heated grill. The duration will vary depending on the type of food, its density and thickness.
Operation Prepare the grill The grill can be used with or without the lava rocks. – Without the lava rocks the rising steam keeps the food being grilled moist. – Grilling with the lava rocks creates a particularly intensive aroma. ...
Operation The grill has 2 heating elements which Grilling can be switched on and controlled in- When grilling make sure that there is dependently. With smaller amounts grill sufficient water in the grill trough. If on the front section and then use the necessary, add more water.
Operation Tips After grilling Switching the grill off. – Pat wet food with kitchen paper to absorb surplus moisture and avoid Clean the grill after each use while it spitting. is still warm to the touch (see "Clean- –...
Safety features Overheating protection Safety switch-off An overheating protection mechanism A safety cut-out ensures that the heater switches the appliance off automatically elements can only heat up when they if the water level in the grill trough drops are lying horizontally and not when they too low.
Cleaning and care Allow the CombiSet to cool down Danger of burning. before cleaning. Before cleaning the appliance make sure that you have switched it off The CombiSet and accessories and that it has cooled down. should be cleaned after each use. ...
Cleaning and care Stainless steel frame/control Operating controls panel Clean the control(s) with a solution of warm water and a little washing-up li- Clean the frame and the control panel quid applied with a soft sponge. with a solution of warm water and a Stubborn soiling should be soaked little washing-up liquid applied with a first.
Cleaning and care Heating elements Grill trough Remove any residues from the heat- After grilling, allow the water in the ing element with a suitable sponge. trough to cool down before draining Lava rocks Place a container large enough to Clean the lava rocks regularly.
Danger of injury. Installation, maintenance and repairs may only be carried out by a suitably qualified and competent person. Repairs and other work by unqualified persons could be dangerous. Miele can- not be held liable for unauthorised work. Do not attempt to open the casing of the CombiSet yourself.
Grilling accessories Griddle CSGP 1300 Large wire frame Handle Cast-iron griddle to place on top of the CS 1312 grill, with a flat and a fluted side Griddle CSGP 1400 Lava rocks Cast-iron griddle to place on top of the...
Page 28
Optional accessories Cleaning and care products Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling, limescale de- posits and aluminium residues Stainless steel conditioning agent 250 ml Removes water marks, flecks and finger prints. Helps keep the appliance looking good for longer.
Safety instructions for installation Fit the wall units and cooker hood before fitting the CombiSet to avoid dam- aging it. The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort.
Safety distances Safety distance above the CombiSet A minimum safety distance must be maintained between the CombiSet and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood a min- imum safety distance of at least 760 mm must be maintained, or if any flammable objects (e.g.
Page 31
CS 1134 CS 1326 CS 1327 CS 1411 100 mm CS 1012 / CS 1012-1 150 mm CS 1421 CS 1312 Not recommended CS 1322 200 mm CS 1034 / CS 1034-1 250 mm CS 1011 / CS 1021 Not recommended...
Page 32
Safety distances Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance ...
Installation notes Seal between the CombiSet Tiled worktop and the worktop Grout lines and the hatched area un- derneath the CombiSet frame must be smooth and even. If they are not the Do not use sealant between the CombiSet will not sit flush with the CombiSet and the worktop.
Building-in dimensions CS 1312 a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L = 2000 mm e Drain tap...
Page 35
Building-in dimensions CS 1322 a Spring clamps b Front c Casing depth d Casing depth including mains connection box with mains connection cable, L = 2000 mm e Drain tap...
Building-in several CombiSets Example: 3 CombiSets a Spring clamps b Spacer bars c Gaps between spacer bars and worktop d Cover strips e CombiSet width minus 8 mm f CombiSet width g CombiSet width minus 8 mm h Worktop cut-out...
Page 37
Building-in several CombiSets Calculating the worktop cut-out The frames of the CombiSets overlap the worktop at the outside right and left by 8 mm on each side. Add up the widths of the CombiSets and subtract 16 mm from this figure. Example: 288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm The CombiSets are 288 mm, 380 mm or 576 mm wide depending on model (see...
Installation Preparing the worktop Make the worktop cut-out as shown in "Building-in dimensions" or as cal- culated (see Building-in several CombiSets). Observe the safety dis- tances (see "Safety distances"). Wooden worktops Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture.
Page 39
Installation Natural stone worktops You will need heavy duty double-side tape (not supplied) to secure the spring clamps and spacer bars. Apply silicone to the side and lower edges of the spring clamps and the spacer bars . Then fill gap between spacer bar ...
Page 40
Installation Building in several CombiSets Installing the CombiSet Push the built-in CombiSet to the Feed the mains connection cable side until the holes in the spacer bar down through the cut-out. can be seen. Starting at the front, position the CombiSet in the worktop cut-out.
Page 41
Installation Connecting the CombiSet Connect the CombiSet(s) to the mains. Check that each CombiSet works. Removing the CombiSet If the CombiSet cannot be accessed from below, you will need a special tool to remove it. If the CombiSet can be accessed from below, push it out from below.
Residual current device Danger of injury. For extra safety, it is advisable to pro- Miele cannot be held liable for unau- tect the CombiSet with a suitable resid- thorised installation, maintenance ual current device (RCD) with a trip and repair work as this can be dan- range of 30 mA.
Page 43
If the mains cable needs to be replaced it must be replaced with a special con- Safety fuses nection cable, type H 05 VV-F (PVC-in- sulated), available from Miele. Completely remove fuses The connection data is quoted on the Automatic circuit breakers data plate.
N.B. A call-out charge will be applied to service visits where the problem could have been resolved as described in these instructions. When contacting your Dealer or Miele, please quote the model and serial number of your appliance. Data plate Space in which to stick the extra data plate supplied with the appliance.