PLAY signal, or when the PLAY key is pressed (S104 ON in the FLKY assy), with the above requirements satisfied. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 61. DV-656A-S...
Page 3
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. DV-656A-S...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING 15–17 "Operating Instructions" FRONT DV-656A-S...
Page 7
ARY7022 Operating Instructions VRD1162 Polyethylene Bag VHL1051 (Italian / Dutch) Pad L VHA1307 (2) CONTRAST TABLE DV-656A-S/WYXJ and DV-656A-K/WYXJ are constructed the same except for the following: DV-656A-S/ DV-656A-K/ Mark No. Symbol and Description WYXJ WYXJ 13 Packing Case VHG2223...
2.2 EXTERIOR SECTION NON-CONTACT SIDE CONTACT SIDE Refer to "2.4 LOADING MECHA ASSY". Refer to "2.3 FRONT PANEL SECTION". DV-656A-S...
Page 9
VRW1889 PCB Holder VEC2283 PCB Holder VEC2283 NSP 23 Base Chassis VNA2521 (2) CONTRAST TABLE DV-656A-S/WYXJ and DV-656A-K/WYXJ are constructed the same except for the following: DV-656A-S/ DV-656A-K/ Mark No. Symbol and Description WYXJ WYXJ 24 Rear Panel VNA2462 VNA2487...
2.3 FRONT PANEL SECTION • Tray Panel Section NON-CONTACT SIDE CONTACT SIDE DV-656A-S...
Page 11
Pioneer Badge See Contrast table (2) Screw BBZ30P100FZK • • • • • • • • • • (2) CONTRAST TABLE DV-656A-S/WYXJ and DV-656A-K/WYXJ are constructed the same except for the following: DV-656A-S/ DV-656A-K/ Mark No. Symbol and Description WYXJ WYXJ...
Carriage DC Motor / 0.3W PXM1027 Screw JGZ17P028FMC Flexible Cable (26P) VDA1864 Screw Z39-019 Connector Assy 2P VKP2253 Tray VNL1920 Float Rubber VEB1327 Belt VEB1330 Stabilizer VNE2253 Loading Base VNL1917 Float Base DVD VNL1918 Drive Cam VNL1919 Gear Pulley VNL1921 Loading Gear VNL1922 DV-656A-S...
Page 13
GYA1001 Daifree No. 23 Daifree No. 23 GEM1036 Tray GEM1036 Tray Concave of unevenness Concave of unevenness Inner side of a ditch Daifree GEM1036 Bottom View Top View Side of the rib Concave of unevenness Daifree Daifree GEM1036 GEM1036 DV-656A-S...
3.3V IC481 LOD POS CN602 SM8707HV (2P) SW1(GNDS) Clock Generator S101 CN402 (17P) Remote V101 Sensor VAW1073 Unit FL TUBE KEYB ASSY SEL IR FLKY ASSY IR101 IC101 PE5314B KEY0 FL Control KEY1 CN201 CN102 CN101 (4P) (4P) (17P) DV-656A-S...
Page 17
AUDIO_L AUDIO_L L IN IC901 MM1505XN RY903 V/Y OUT V IN IC902 MM1507XN AV CONNECTOR CN901 JA902 (RGB) - TV (19P) L OUT L IN IC903 MM1507XN B IN G IN RY904 R/C IN V OUT RY905 V IN DV-656A-S...
3.2 LOAB ASSY and OVERALL WIRING DIAGRAM SACDB ASSY (VWG2378) JACB ASSY (VWV1914) SCRB ASSY Note : When ordering service parts, be sure (VWV1922) to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". DV-656A-S...
Page 21
KEYB ASSY (VWG2366) FLKY ASSY (VWG2355) POWER SUPPLY UNIT (VWR1352) DVDM ASSY (VWS1539) SPINDLE MOTOR : VXX1088 STEPPING MOTOR : VXM1090 LOADING MOTOR ASSY LOAB ASSY : VXX2505 (VWG2346) DV-656A-S...
: FOCUS SERVO LOOP LINE Buffer (RF) : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE Buffer (RF) (RF_V) (RF_A) (RF) Buffer (RF) (RF) LD Driver for DVD SW for LD Driver Defect Signal for CD (RF) CN601 (F) (F) DV-656A-S...
Page 23
(RF_V) VCO Circuit (RF_V) RF Amp. (RF for SACD Water Mark detection) : The power supply is shown with the marked box. (RF_A) DV-656A-S...
3.5 DVDM ASSY 3/4 [EBY/AV1 BLOCK] DVDM ASSY (VWS1539) (AD) (AD) DVD data Decoder (RF_V) (RF_V) DV-656A-S...
Page 27
: The power supply is shown with the marked box. MPEG, DVD-Audio, DTS Decoder Progressive scan Processer (RF_V) : RF (VIDEO) SIGNAL ROUTE (VD) : VIDEO DATA SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE DV-656A-S...
Audio DAC for Front channel (2 ch) 21 22 24 23 +8V Regulator +5V Regulator DIGITAL AUDIO OUT COAXIAL CN551 DIGITAL AUDIO OUT OPTICAL Audio DAC for Ls, Rs (2 ch) Audio DAC for C, LFE (Sub Woofer) (2 ch) DV-656A-S...
Page 31
(with LPF) Ls ch. for Mute Control Rs ch. Signal Center LFE ch. (Sub Woofer) Audio out Audio Amp. : The power supply is shown with the marked box. (with LPF) for Mute Control Signal LPF: Low Pass Filter DV-656A-S...
: Y SIGNAL ROUTE : C SIGNAL ROUTE (Pb) : Pb SIGNAL ROUTE (Pr) : Pr SIGNAL ROUTE : R SIGNAL ROUTE : G SIGNAL ROUTE : B SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE : AUDIO SIGNAL ROUTE DV-656A-S...
Page 33
: The power supply is shown with the marked box. Composite Video out (Y/G) (Pb/B) (Pr/R) Video out (Pb) (Pr) Component Video out CN901 DV-656A-S...
3.11 SCRB ASSY SCRB ASSY (VWV1922) Buffer Buffer CN702 (R/C) Video Amp. with SW Video Amp. with SW (Y/V) (Y/V) Video Amp. DV-656A-S...
Page 39
: R SIGNAL ROUTE : AUDIO SIGNAL ROUTE : G SIGNAL ROUTE : B SIGNAL ROUTE RY901-RY905: Relay SW (R/C) (Y/V) (R/C) (R/C) (R/C) (R/C) (R/C) (Y/V) (Y/V) (Y/V) (Y/V) : The power supply is shown with the marked box. DV-656A-S...
Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator SIDE A SIDE B LOAB ASSY (VNP1836-B) CN602 CN601 CN601 CN602 CN103 LOADING MOTOR ASSY DV-656A-S...
Tangential Radial adjustment adjustment screw screw [Electrical Part] Electrical adjustments are not required. 6.2 JIGS AND MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1067) Screw tight (GYL1001) DVD test disc Precise screwdriver (GGV1025) DV-656A-S...
Purpose: To set the sweep which was correct with the individual Traverse mechanism. Be sure to perform the following step finally when replaced Pickup, Traverse Mechanism and Spindle Motor. CLEAR GGF1067 Test mode remote control unit (It is necessary when performed adjustment procedure Ÿ.) DV-656A-S...
An address is displayed < When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY CHP/TIM Press keys in order 030000 TEST MODE: OFF POWER GGF1067 Test mode remote control unit DV-656A-S...
Mechanism Base and turn each screw to adjust the height. (Refer to "6.1 ADJUSTMENT ITEMS AND LOCATION".) Spacer for Height adjustment Note: Turn the Short switch to Short side when Turn a flat side removing the Pickup Flexible Cable. into bottom (Refer to "7.1.9 DISASSEBLY".) DV-656A-S...
Page 63
J4 : Min If error rate is OK, Disc playback normally. • The measurement of block error rate locks a root of tangential and radial adjustment screws with the Screw tight, and go to step Screw tight: GYL1001 Test mode end DV-656A-S...
Page 64
Initialize the Focus Sweep Setting Purpose: To set the sweep which was correct with the individual Traverse mechanism. Turn on the Player POWER CLEAR Note: Be sure to perform this step when replaced the Pickup or Traverse mechanism. DV-656A-S...
[Player's ID Data Setting] number. [Player's ID Number Setting] ID Number ? > 0 0 0 0 0 0 0 0 1 OK ? <PLAY> Compare Mode <SEARCH> Enter Loading The ID Data Disc ! Input ID Number ! DV-656A-S...
Page 66
Compare Compare > * * * * * * * * * > 0 0 0 0 0 0 0 0 1 OK ? <CLEAR> Exit <PLAY> Enter <STOP> Memory Clear Input ID Number ! Input ID Number ! DV-656A-S...
Replace the Traverse Mechanism Assy or Pickup. Note : When a DVD disc or a CD disc is played in the test mode, this function is effective. Character in bold : Item name : Information display Laser diode current value DV-656A-S...
: [IN ] CD active area : [CD] $ Version of the flash ROM [V: ∗. ∗ ∗ ∗] Flash ROM size [FLSH = ∗] % Revision of the system controller [S: ∗ . ∗ / ∗ ∗ ∗ ] DV-656A-S...
Page 69
2 C1 error value of DVD [ER – ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ] _ Internal operation mode of mechanism controller [MM – ∗ ∗ : ∗ ∗] Internal mechanism mode (2 digits) and internal mechanism step (2 digits) of the mechanism controller DV-656A-S...
Display the mechanism error history and self diagnosis result by pressing the "CHP / TIM" key once again. Afterwards press the "CHP / TIM" key with toggle and change the display. Display screen of mechanism error history and self diagnosis result DV-656A-S...
EDC Error which occurred in the same block in succession. will be increased. As for this, CPU power is used for update of OSD drawing, symptoms occur so that control of VBR Buffer is not in time. Indication contents DV-656A-S...
Were not able to playback from the disc distinction process. 38 Disc-type- PLAY or STOP was not completed by backup operation of the disc distinction. Open sensing error Distinguished it from the blank disc in the ATB process completion. DV-656A-S...
Page 73
Subcode check No frame could be read for 3 failure during Stop seconds or more. playback ID can not read An ID could not be read within 1 second after the AFB Opens during startup tracking on. (ID readout failure) DV-656A-S...
Page 74
10 etc. check sum error AV1 access error No operation or it becomes debugging bit3=1 08 etc. (read, write NG) indication if the power is able to ON. bit2=1 04 etc. LSI11 access error bit0=1 01 etc. SRAM access error DV-656A-S...
DVDM Assy CN105-pin 12 (INSIDE SW signal) • Check the loading drive signal : IC351-pin 14, 15, 16 • Check the +6V and +12V power supply voltage (If above voltage is not supplied, check the micro-fuse P101 and P102.) DV-656A-S...
Page 78
• Check digital data of video and audio signals (audio signals: 3 line data, video signals: or beeing damaged? (noisy) 8bit data) shown to each schematic diagram and an analog signal line. In addition, check CLK. audio system: 22/24MHz, video system: 27MHz Indicate the error message. Refer to the section "7.1.6 ERROR DISPLAY". DV-656A-S...
Close the Tray (0). → Clamp the Test Disc. Release the PCB Support. Remove the DVDM Assy. Turn power OFF. PCB Support Pull out the Power Cord from the outlet. Cutting Pliers DVDM Assy Test Disc (Flexible Cable) This is not installed in this unit. DV-656A-S...
Page 80
Connect two Extension Cables and a Extension Board as figure below. 17P Extension Cable 21P Extension Cable for Service for Service [GGF1157] [GGD1298] Loading Mecha Assy POWER SUPPLY Unit CN561 CN402 CN101 JACB Assy SACDB Assy (DV-45A Only) DVDM Assy Extension Board for Service [GGF1430] Front Panel Section Diagnosis DV-656A-S...
Page 82
Caution in the Tray Insertion × 4 In the Tray insertion, insert it after matching a triangle mark of the Loading Base and a position of pin of the Drive Cam. Triangle Mark Loading Base Loading Mecha Assy DVDM Assy Drive Cam DV-656A-S...
Page 83
Screw is locked with Silicone Adhesive. Please lock it with Silicone Adhesive when installs it. Unhook ( × 4) Remove the Traverse Mechanism Assy-S Silicone Adhesive GEM1037 Slider × 2 Hold Spring Pickup Assy-S Joint × 2 Traverse Mechanism Assy-S Silicone Adhesive GEM1037 DV-656A-S...
Page 84
Move the Pickup to the innermost of the disc Perform the styling as shown in figure below. Lose slack Fold position of step Bottom View Bottom View Fold at the position Reference line of reference line. Bottom View Bottom View DV-656A-S...
Page 85
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC LA9704W, LC78652W, BA6664FM, SM8707HV, PD6345A, M65776AFP, AD7172KST, PCM1738EG-3, DSD1702EG, LA73054, CXD2753R, PE5314B, PE5286A 7 LA9704W (DVDM ASSY : IC101) • RF IC ¶ Block Diagram DV-656A-S...
Page 86
¶ Pin Function c i f z i l i f i l l l u l l u DV-656A-S...
Page 89
¶ Pin Function t f i − − l l i t t i y t i t l i − − − − a i l t l i − DV-656A-S...
Page 90
− − l l i l i f − t l i f t l i f t l i f − − − − − l l i − l l i t t i − − DV-656A-S...
Page 91
Control reference pin of output voltage Output pin Output voltage control pin GND pin Power save pin FG signal output pin Power supply pin Gain switching pin Hall signal input pins Motor power pin Resistor connection pin for output current detection Hall bias pin DV-656A-S...
Page 92
• Clock Generate IC ¶ Pin Arrangement ¶ Pin Function . r i x i f x i f x i f x i f n i l L " : " " : " l l u x i f – DV-656A-S...
7.4 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DV-656A-S...