Table of Contents
Related Manuals for Miele ESW 4700
Summary of Contents for Miele ESW 4700
- Page 1 Operating and Installation Instructions Built-in Warming Drawer ESW 4700 / ESW 4710 / ESW 4720 ESW 4800 / ESW 4810 / ESW 4820 To prevent accidents and machine damages, read these instructions before installation or use. M.-Nr. 06 543 320...
-
Page 3: Table Of Contents
IMPORTANT SAFETY INSTRUCTIONS ....... . . 4 Guide to the warming drawer ........8 Guide to the controls . -
Page 4: Important Safety Instructions
Installation, repair and mainten- ance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. Before installation or service, disconnect the power supply to the work area by removing the fuse, "tripping"... - Page 5 However, under certain circumstances it may be possible for installation in these applications. Please contact the nearest Miele Dealer or the Miele Technical Service Department with specific requirements. IMPORTANT SAFETY INSTRUCTIONS To prevent burns do not touch hot surfaces, use handles or knobs.
- Page 6 To prevent injuries, do not use accessories not recommended by Miele. Before cleaning the appliance, trip the circuit breaker and allow the appliance to cool. Do not use a steam cleaner to clean the drawer.
-
Page 7: General Notes
General notes Children should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance. Caution: Do not store items of interest to children in cabinets above or in the warming drawer. -
Page 8: Guide To The Warming Drawer
Guide to the warming drawer a Timer b Temperature selector c Humidity control d Non-slip mat e Rack f Drawer... -
Page 9: Guide To The Controls
The warming drawer is operated by the timer, the temperature selector, and the humidity control. The controls are only visible when the drawer is open. Once the warming drawer begins to heat the circulation fan will turn on to evenly heat the drawer. When the selected temperature is reached, the heat and the fan will shut off to prevent food from drying out. -
Page 10: Temperature Selector
Guide to the controls Temperature selector The temperature is infinitely variable between the basic setting (see illustration) and the "High" setting. The temperature settings: – Basic setting: 97°F (36 °C) – Low: 140 °F (60 °C) – Medium: 176 °F (80 °C) –... -
Page 11: Humidity Control
Humidity control The humidity control adjusts the humidity within the drawer. The humidity control can be set anywhere between "Moist" and "Dry". Use oven mitts when adjusting the humidity control. The control may become hot during use. Guide to the controls –... -
Page 12: Temperature And Humidity Suggestions
Guide to the controls Temperature and Humidity Suggestions Food Bacon Beef Medium / Well Beef Rare Bread hard roles Bread soft rolls Bread proofing Casserole, crisp top Casserole, moist Eggs Fish / Seafood Fish sticks Fried foods Fruit Gravy, cream sauces Lamb Oatmeal Pancakes... -
Page 13: Loading The Warming Drawer
The rack can be inserted in three positions: middle, left or right. ^ Insert the rack into the slots of the rear wall in the drawer and then slide the front of the rack into position. Additional racks are available for purchase from Miele. -
Page 14: Tips
Loading the warming drawer Tips – To keep different foods hot, set the temperature for the food requiring the highest temperature setting. Place the food needing the highest setting on the rack and the other food on the floor of the drawer. –... -
Page 15: Using The Warming Drawer
Keeping food warm For best results, preheat the warming drawer before warming food. ^ Open the drawer. ^ Turn the timer to the desired time setting. ^ Turn the temperature selector to the desired temperature setting. ^ Slide the humidity control to the desired humidity level. -
Page 16: Warming Dishes
Using the warming drawer Warming dishes The warming drawer can also be used to warm dishes. Do not preheat the drawer before warming dishes. Only use heat resistant dishes. ^ Open the drawer. ^ Place the dishes in the drawer. Arrange dishes evenly in the drawer and on the rack. -
Page 17: Warming Drawer Care
, CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Do not clean or remove the warming drawer until it has cooled. Danger of burns! Warming drawer care Appliance front and control panel ^ All external surfaces and controls can... -
Page 18: Drawer
Warming drawer care Drawer The drawer can be removed for easier cleaning. Removing the drawer ^ Pull the drawer completely out and loosen the nuts. ^ Carefully lift the drawer and pull it slowly out. Set the drawer down on a flat, stable surface. -
Page 19: Frequently Asked Questions
,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause an injury or machine damage. Some minor problems can be fixed without a service call. What if the drawer does not heat? Possible fault There is no power to the warming drawer. - Page 20 Frequently asked questions What if the drawer cannot be closed properly? – Check that the drawer is correctly installed on the runners. – Check if the hooks on the underside of the drawer, on the left and right sides, are in the correct position. If a hook has slipped off the track, push it towards the rear of the drawer and up until it clicks into place.
-
Page 21: Technical Service
Miele’s Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home. -
Page 23: Installation Instructions
Installation Instructions... -
Page 24: Help Protect Our Environment
Help protect our environment Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. -
Page 25: Electrical Connection
CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held... -
Page 26: Installation
Installation Installation tips – The warming drawer should be placed at a convenient height for easy access. – The drawer should be installed clear of drafts caused by open doors and windows. – Proper clearance must be allowed for the warming drawer to open with out interference. - Page 27 Installation Dimensions for Solo Installation ESW 47x0 a Material must be moisture resistant...
- Page 28 Installation ESW 48x0 a Material must be moisture resistant 2 4 " ( 6 1 " 1 / 2 " - 0 - 7 ( 6 6 " / 1 6 6 " 6 " 1 "...
- Page 29 Installation Dimensions for a combination installation with an oven ESW 47x0 a Material must be moisture resistant...
- Page 30 Installation ESW 48x0 a Material must be moisture resistant...
-
Page 31: Installing The Warming Drawer
Installing the warming drawer ^ Remove the drawer from the casing before installing the appliance into the cabinetry. Removing the drawer ^ Pull the drawer completely out and loosen the nuts. ^ Carefully lift the drawer and pull it slowly out. Set the drawer down on a flat, stable surface. -
Page 32: Integrated Installations Models 4700 Fb And 4800 Fb
Installation Integrated installations Models 4700 FB and 4800 FB Custom made front panels can be installed with models 4700 FB and 4800 FB. Panel dimensions 4700 FB Width 27 " (695 mm) Height 11" (279 mm) 4800 FB Width 29 "... - Page 33 f Press the custom panel tightly onto the removed panel. g Screw the removed panel to the custom panel with the eight screws. h Hook the panels into the bottom on and secure at the top with two screws making sure the seal is seated correctly.
- Page 36 Alteration rights reserved / 3206 M.-Nr. 06 543 320 / 06 en - US...